HIAB Hooklift Multilift XR S Series Скачать руководство пользователя страница 124

Страница: 124 / 160

124

4/2018

113175421

XR14S/16S/18S/21S/26S/30S

Hooklift Multilift XR S

Service Manual

103

115

116

101

114

117

108

101

108

114

Emergency operation

CAUTION!

Internal safety functions of the device do not work

in manual control mode. Therefore, be especially

careful when carrying out the movements.

If a failure happens in the

electric system of the device,

the device may be restored to

its normal state, by operating

the control valve manually:

1. Press down the button

located at the end of

valve for needed direction

(101 or 114) and hold it

down.

2. Press down the button

located at the end of free

circulation valve (108).

3. Release the buttons

when you would like to

stop the movement.

Note!

The valve stem return spring (101 or 114) is

rather rigid and requires effort to push the button

to the bottom.

You can use the emergency movement lever

MU111568801 (additional equipment, located

behind the valve stand) as an auxiliary tool.

Содержание Hooklift Multilift XR S Series

































































































































































Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Бренды по названию

Популярные бренды

HIAB Hooklift Multilift XR S Series, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание Hooklift Multilift XR S Series

Отзывы:

Бренды по названию

Популярные бренды