Hi-Target ZTS-320 Series Скачать руководство пользователя страница 26

Страница: 26 / 97

4. Preparations before measurements

4.1 Unpacking and storing instruments

Unpacking
Lay down the tool box gently with the top side facing up.

Open the lock and unpack and take out the instrument.

Storage
Cover the telescope cover. Make sure that the vertical

clamping screw and the level bubble face upwards. Lay down the
instrument into the tool box ( with objective lens of the telescope
facing downwards.). Tighten the vertical clamping screw gently
and cover the box, then Lock the box.

4.2 Set up the instrument

Reference for operation:
Install the instrument onto the tripod gently , then level and

center the instrument to ensure the accuracy of the measurement
result.

4.2.1 Using plumbs to center and level (align)

1) Set up the tripod

①

Position tripod legs so that the plummet is aimed to the

ground mark point. Turn the focusing ring of the optical
plummet to focus.

②

Make sure that the center of the tripod top is right

above the station.

③

Stamp the tripod on the ground with your feet.

2) Install the instrument onto the tripod
Mount the instrument on the tripod head. Support it with

one hand, and tighten the centering screw on the bottom of the
unit to make sure it is secured to the tripod.

3) Using the circular level to level the instrument coarsely

①

Twist and adjust the two leveling screw A and B on the

bottom of the instrument until the bubbles of the circular level
moves to the line perpendicular to the center line the screw A
and B.

②

Twist and adjust leveling screw C to move the bubble to

the center of the circular level.

Содержание ZTS-320 Series


































































































Результаты поиска

Содержание ZTS-320 Series

Отзывы:

Hi-Target ZTS-320 Series, Руководство пользователя, Страница: 26 / 97

Результаты поиска

Содержание ZTS-320 Series

Отзывы: