HHP IMAGETEAM 5600 Скачать руководство пользователя страница 52

Страница: 52 / 144

5 - 4

tax = E4nnxx

...zz

where nn is the total count of both

characters to be replaced plus replacement characters; xx

defines charac-

ters to be replaced and xx

defines replacement characters, continuing

through zz

and zz

E5 Terminates character replacement.

Syntax = E5

FE Compare character in current cursor position to the character “xx.” If char-

acters are equal, increment cursor. If characters are not equal, no format
match.

Syntax = FExx

(xx stands for the hex value for an ASCII code, see

ASCII Conversion Chart (Code Page 1252)

on page A-2.)

EC Check to make sure there is an ASCII number at the current cursor position.

If character is not numeric, format is aborted.

Syntax = EC

ED Check to make sure there is a non-numeric ASCII character at the current

cursor position. If character is numeric, format is aborted.

Syntax = ED

Data Format Editor

Enter Data Format

* Default Data Format

Clear One Data Format

Save

Discard

Clear All Data Formats

Содержание IMAGETEAM 5600

















































































































































Результаты поиска

Содержание IMAGETEAM 5600

Отзывы:

HHP IMAGETEAM 5600, Руководство пользователя, Страница: 52 / 144

Результаты поиска

Содержание IMAGETEAM 5600

Отзывы: