5. Technical data
Overall height:
1210 mm
Overall length:
1500 mm
Fork length:
1150 mm
Fork height min.:
80 mm
Fork height max.:
190 mm
Fork width single:
153 mm
Fork width total:
540 mm
Lift max.:
110 mm
Load:
2500 kg
Weight approx.:
66 kg
Steering wheels Ø:
180 mm
Load-bearing rollers Ø:
80 mm
6. Assembly
Note:
The maintenance plate (Fig. 2 / Item D) must
not be removed throughout the assembly work.
1.
(Fig. 2) Use a pin driver or screwdriver to knock
the clamping sleeve (A) out of the bolt (B). Then
remove the bolt (B) from the drawbar mount (C).
2.
(Fig. 3 / 4) Insert the bolt (B) through the hole in
the drawbar mount (C) and the drawbar (3). Then
knock the clamping sleeve (A) back into the bolt
(B). As you do so, watch the clamping sleeve
passage (E) in the drawbar mount (C).
3.
(Fig. 3) Pass the control chain (F) through the
hole in the bolt (B) so that the hydraulics system
works.
4.
(Fig. 5) Hook the setting screw (H) with the pre-
mounted hex nut (K) into the hydraulics lever (L).
5.
(Fig. 5) Press down the drawbar and remove the
maintenance plate (D). Keep the maintenance
plate in a safe place for subsequent maintenance
work on the hydraulics.
Note:
The equipment can be optionally equipped with
a foot-activated parking brake. If required, please
contact your customer service team.
Operating the foot-activated parking brake:
Push the brake to the right as far as the stop – the
wheels will be blocked.
Push the brake to the left – the wheels will be
released again.
7. Functions
Important! Note the safety information (section 1.)
and Figure 7.
On the drawbar is a sticker showing the positions of
the handle switch (Fig. 6).
1 = Lower (lowering position)
2 = Travel (traveling position)
3 = Lift (lifting position)
The pallet lifting truck is allowed to be parked only
when the lifting forks are lowered.
The following functions are possible and were already
set in the factory.
7.1 Lifting the load (Fig. 1)
Press down the control lever (2) (lifting position).
Then pump the drawbar (3) up and down several
times. The load will be lifted.
7.2 Pulling the load (Fig. 1)
Pull up the control lever (2) into the middle position
(traveling position). In this position the hydraulics
cannot be used for lifting or lowering.
7.3 Lowering the load (Fig. 1)
With the pallet lifting truck at a standstill, pull up the
control lever (2) to the very top (lowering position).
The load will be lowered. When you now release the
control lever (2), it will automatically return to the
middle position (traveling position).
8. Setting the hydraulics control
system
The functions described in section 7. will not work
correctly if the hydraulics control settings are altered.
In this case you must re-set the hydraulics control
system.
8.1 The lifting forks rise when the control lever is
in the traveling position
(Fig. 5) Turn the hex nut (K) on the setting screw (H)
clockwise to the point where the lifting forks no longer
rise and the traveling position works correctly.
8.2 The lifting forks descend when the control
lever is in the traveling position
(Fig. 5) Turn the hex nut (K) on the setting screw (H)
counter-clockwise to the point where the lifting forks
no longer descend and the traveling position works
correctly.
10
GB
Anleitung_AHW_2500_SPK7:_ 22.08.2011 13:26 Uhr Seite 10
Содержание 20.225.28
