Helion Select Four 10 sc страница 24 Скачать руководство пользователя

Страница: 24 / 42

Appendix A: Troubleshooting Guide for the Reaktor Power System

Problem / Symptom

Possible Cause

Possible Solution

ESC will not set to

transmitter

Receiver and transmitter not bound Try re-pairing
Throttle Channel not set to Reverse Unless using Futaba radio, set Th channel to Re-

verse

Batteries dead in car or transmitter Replace batteries

Transmitter is too close to vehicle

Hold transmitter farther away from vehicle

After turning ON, the

motor won’t work and

no sound comes from

motor

The connections between the bat-

tery and the ESC are not correct

Check the power connections. Replace the connec-

tors if they are worn or damaged

Car slowed down or

stopped drastically

during run

Battery voltage too low, LVC active

Charge or change batteries

ESC over-temp protection active

Turn off ESC and allow ESC and motor to cool before

running again

ESC Over current protection active

Change operating conditions to ones that are not

as hard on the electronics, i.e. move from grass to

asphalt.
Reduce pinion gear size on the motor to reduce load

on the ESC

Car doesn’t accelerate Ensure the proper punch mode is

used

Change punch mode based on battery you are using

Reverse not working

Reverse mode has been disabled

in ESC

Follow setup instructions to turn back on

ESC was improperly set to trans-

mitter

Re-set to transmitter, ensure Th channel is set to

Reverse for non Futaba transmitters

EPA on transmitter has been turned

down for reverse

Adjust EPA’s to 100% and recalibrate ESC to trans-

mitter

Motor only goes in

reverse or goes in

reverse when I pull

trigger to go forward

Throttle Channel not set to Reverse Unless using Futaba radio, set Th channel to Re-

verse and reset ESC to transmitter

Motor connected to ESC improperly Switch any two motor wires

EPA on transmitter has been turned

down for reverse

Adjust EPA’s to 100% and reset ESC to transmitter

Содержание Select Four 10 sc











































Результаты поиска

Содержание Select Four 10 sc

Отзывы:

Похожие инструкции для Select Four 10 sc

Бренды по названию

Популярные бренды

Helion Select Four 10 sc, Руководство пользователя и техническая информация

Результаты поиска

Содержание Select Four 10 sc

Отзывы:

Похожие инструкции для Select Four 10 sc

Бренды по названию

Популярные бренды