HEIL PT 1000 Скачать руководство пользователя

Страница: 83 / 202

Issued September 2017
Controls, Switches, and Indicator Lights

Printed in U.S.A.

OPTIONAL OUTSIDE CONTROLS
(CONTINUED)

F. LATCH BAR ASSEMBLY

You use the latch bar assembly to secure a refuse
container BEFORE you raise or lower the container with
a reeving mechanism, winch or roll bar. Refer to the
figure on the right.

1. You ROTATE the latch assemblies UP which

RELEASES the latch bars and they can ROTATE
DOWN.

2. You move the refuse container to the tailgate into

position for latching its trunnion bar.

3. You ROTATE the latch bars UP and ROTATE the

latch bar assemblies DOWN over the latch bars. This
locks container’s trunnion bar in the latch bar
assembly.

4. A “bash bar” prevents the container from over-

rotating into the hopper.

Figure 52. Latch Bar Assembly

Содержание PT 1000



























































































































































































Результаты поиска

Содержание PT 1000

Отзывы:

Похожие инструкции для PT 1000

Бренды по названию

Популярные бренды

HEIL PT 1000, Руководство по эксплуатации

Результаты поиска

Содержание PT 1000

Отзывы:

Похожие инструкции для PT 1000

Бренды по названию

Популярные бренды