background image

 

Tribute Model #8050 
Manual: 6400-40423 

Revision: 3 - 6/23/2011

  

 

Tribute DV

  

(

Model 8050)  

GAS-FIRED

 

DIRECT-VENT

 

HEATER 

Owner’s Manual  

& Installation Guide 

READ THIS OWNER’S MANUAL 

Operate And Maintain This Gas Heater According To This Instruction Manual. 

Save These Instructions! 

 

WARNING: IF THE INFORMATION IN THESE 
INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A 
FIRE OR EXPLOSION CAN RESULT CAUSING 
PROPERTY DAMAGE, PERSONAL INJURY OR 
LOSS OF LIFE. 

Do not store or use gasoline or other flammable vapors and 
liquids near this or any other gas appliance. 

  WHAT TO DO IF YOU SMELL GAS: 

  Do not try to light any appliance. 
  Do not touch electrical switches; do not use the phone 

in your building. 

  Immediately call your gas supplier from a        

neighbor’s phone. Follow your gas supplier’s        
instructions. 

  If you cannot reach your gas supplier, call the fire 

department. 

A qualified installer, service agency or gas supplier must 
perform installation and service. The Commonwealth of 
Massachusetts requires that a licensed gas fitter or licensed 
plumber install all gas lines and gas fittings.

 

 

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE 
LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE 
POUR RÉDUIRE AU MINIMUM LE RISQUE D’INCENDIE 
OU POUR ÉVITER TOUT DOMMAGE MATÉERIEL, 
TOUTE BLESSURE OU LA MORT. 

Ne pas entresposer ni utiliser d’essence ni d’autre vaperurs ou 
liquides inflammables dans le voisinage de cet apprareil ou de 
tout autre appareil. 

 QUE FAIRE SI VOUS SENTEZ UNE ODEUR  DE GAZ: 

 

Ne pas tenter d’allumer d’appareil. 

 

Ne touchez à aucun interrupteur. Ne pas vous servir des 
téléphones se trouvant dans le batiment où vous vous 
trouvez. 

 

Appelez immédiatement votre fournisseur de gaz depuis 
un voisin.  Suivez les instructions du fournisseur. 

 

Si vous ne pouvez rejoindre le fournisseur de gaz, appelez 
le service des incendies. 

L’installation et service doit être exécuté par un installateur 
qualifié, agence de service ou le fournisseur de gaz.

 

Содержание Tribute DV 8050





































Отзывы: