Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 7

Страница: 7 / 54

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

Figure 2.5

- Minimum wall centerline.

D. Hearth Requirements

The Oxford Heater must be installed on rigid flooring. When

the heater is installed directly on any combustible surface

other than wood flooring, a metal or wood panel extending

the full width and depth of the unit must be used as the

hearth. There are no other hearth requirements.

E. Clearances to Combustibles

Figure 2.4

- Corner installation, minimum corner clearances.

Corner Installation:

Minimum Clearance

Direct Vent and Natural Vent

Stove Clearances

4" (102 mm)

ST129c

Dutchwest

corner specs

01/19

Figure 2.3

- Parallel installation, minimum back and side clearances.

Parallel Installation:

Minimum Clearance

Direct Vent and Natural Vent

Stove Clearances

4" (102 mm)

ST128b

Stardance

flue centerline

01/19

Wall Centerline from Floor

Effective Minimum (A)
Wall Thimble

57-1/2" (1461 mm) (HHT Pipe)

Centerline

53-1/2" (1359 mm) (Simpson DuraVent Pipe)

ST1121

wall thimble

01/19

Figure 2.6

- Dimensions and clearances to ceiling or alcove.

Wall and Ceiling Clearances

Rear Wall

4" (102 mm)

Minimum Clearance

45-1/2" (1156 mm)

Minimum Alcove Height

73-1/2" (1867 mm)

Maximum Alcove Height

48" (1220 mm)

Sidewall Clearance

4" (120 mm)

ST1122

Min. clearance

01/19

Содержание OXDV30-IPI























































Результаты поиска

Содержание OXDV30-IPI

Отзывы:

Hearth & Home OXDV30-IPI, Инструкция по установке и эксплуатации, Страница: 7 / 54

Результаты поиска

Содержание OXDV30-IPI

Отзывы: