Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 54

Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 38

38

38

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

J. Burner, Pilot & Control Compartment

Keep the control compartment and burner areas clean by

vacuuming or brushing at least twice a year. Make sure the

burner porting, pilot air opening and burner air opening are

free of obstructions at all times.

Pilot Flame

The flames from the pilot should be visually checked as

soon as the heater is installed and periodically during normal

operation. The pilot flame must always be present when the

stove is in operation, Figure 6.4. The pilot flame has three

distinct flames, one engulfing the sensor, one engulfing the

thermopile, and the other reaching to the main burner.

WARNING

!

Turn off gas before servicing stove. It is recommended that

a qualified service technician perform these check-ups at

the beginning of each heating season

Figure 6.4

- Pilot Flame

CO105d

Pilot flame

6/07 djt

Burner

Inspect area around the injector. Remove any lint or foreign

material with a brush or vacuum.

Burner Flame

The flames from the burner should be visually checked as

soon as the heater is installed and periodically during normal

operation. In normal operation, at full rate, and after operating

for about 15 to 30 minutes, the flame should be yellow.

NOTE: The type of installation, vent system configuration,

and wind effects may cause the flame patterns to vary.

«
...
36
37
38
39
40
...
»

Содержание OXDV30-IPI























































Отзывы:

Нет отзывов