Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 31

Страница: 31 / 54

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

A. Operation

The Oxford is to be operated with the front glass in place.

Ensure the safety barrier screen is in place during operation.

B. Lighting Instructions

Read these instructions carefully and familiarize yourself with

the lighting instructions.

Section F, “Lighting and Operating

Instructions”

. Locate the pilot assembly, Figure 6.1. Follow

the lighting instructions in this manual exactly.
During the first fire, it is not unusual to smell some odor

associated with new logs, paint and metal being heated.

Odors should dissipate within the first eight to ten hours,

however, you can open a window to provide fresh air to

alleviate the condition.

C. Pilot and Burner Inspection

Each time you light your heater check that the pilot flame and

burner flame patterns are as shown in Figure 6.2. If flame

patterns are incorrect, turn the heater off. Contact your dealer

or a qualified gas technician for assistance. Do not operate

the heater until the pilot flame is correct.
Follow regular maintenance procedures as described in the

Cleaning and Maintenance section of this manual.

E. Flame & Temperature Adjustment

For OXDV30 models which are equipped with HI/LO valves,

flame adjustment is accomplished by rotating the HI/LO

adjustment knob located near the center of the gas control

valve, Figure 6.3.

D. Flame Characteristics

It is important to periodically perform a visual check of the

pilot and the burner flames. Compare them to Figure 6.2. If

any of the flames appear abnormal, call a service person.

Figure 6.2

- Correct pilot and burner flame appearance.

Figure 6.3

- Flame adjustment knob

FP390

FLAME ADJUSTMENT KNOB

11/21/96

Turn

counterclockwise

to increase

flame height

Turn clockwise

to decrease

flame height

Operating Instructions

ST769

Dutchwest

pilot location

5/15/03 djt

Pilot Assembly

Figure 6.1

- Pilot assembly location.

LG142

Stardance

Install logs 2

12/11/00 djt

Red

Glow

Содержание OXDV30-IPI























































Результаты поиска

Содержание OXDV30-IPI

Отзывы:

Hearth & Home OXDV30-IPI, Инструкция по установке и эксплуатации, Страница: 31 / 54

Результаты поиска

Содержание OXDV30-IPI

Отзывы: