Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 30

Страница: 30 / 54

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

DANGER

HOT GLASS

WILL

CAUSE BURNS

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

Un panneau vitré chaud

peut

causer des brûlures.

Laissez refroidir le panneau

vitr

avant d’y toucher.

Ne laisser jamais

les enfants

toucher le panneau vitr

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this

appliance and shall be installed.

Une barrière visant à réduire le risque de brûlure

par le hublot chaude est fournie avec cet

appareil et doit être installé.

DANGER

H. Install the Mesh and Grille

Place the mesh and grille on the top of the Oxford stove to

complete assembly.

NOTE: A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance and

shall be installed for the protection of children and other

at risk individuals. If the barrier becomes damaged, the

barrier shall be replaced with the manufacturer's barrier

for this appliance.* Any safety screen, guard, or barrier

removed for servicing the appliance must be replaced

prior to operating the appliance.

* See parts list for model number.

The safety barrier has been designed to work with the doors

open or closed.
1. Remove screen from packaging.
2. Place the two bottom hooks over the bottom edge of the

stove opening, Figure 5.2.

3. Press the screen against the stove snapping the two spring

fingers until the screen fits securely in place.

NOTE: It is the responsibility of the installer to ensure the

barrier is affixed to the stove at the time of installation.

CERTIFIED

AFETY

ARRIER

Figure 5.2

- Install safety barrier screen.

WARNING

The safety screen barrier must be installed after the glass

front is in place. It is not a replacement for the glass and

the unit must not be operated without the glass in place.

F. Fuel Conversion

• This appliance ships with a Natural Gas to Propane

Conversions Kit with installation instructions included.

• Make sure the appliance is compatible with available gas

types.

• Conversions must be made by a qualified service

technician using Hearth & Home Technologies specified

and approved parts.

G. Install the Safety Barrier

Spring

fingers

Hooks

Содержание OXDV30-IPI























































Результаты поиска

Содержание OXDV30-IPI

Отзывы:

Hearth & Home OXDV30-IPI, Инструкция по установке и эксплуатации, Страница: 30 / 54

Результаты поиска

Содержание OXDV30-IPI

Отзывы: