Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 26

Страница: 26 / 54

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

Complete the Assembly

• Open the swiveling latches (cams) on the top left and

right corners of the glass frame.

• Position the glass and frame against the firebox by

placing the bottom edge on the brackets on the bottom

face of the firebox.

• Swing the assembly against the firebox, and close the

latches firmly against the pins protruding from the firebox

top.

G. Thermostat Connection (Optional) Millivolt

Use only a thermostat rated for 500 millivolts.
Check the table below for the appropriate gauge thermostat

wire to use for the length of lead required in your installation.

Thermostat

Wire / Gauge

Maximum Run

20 Feet

20-40 Feet

up to 60 Feet

1. Install the wall thermostat in the desired location and run

the wires to the stove location. Terminate these leads

with 1/4” female connectors.

2. Connect the thermostat wires to the valve, Figure 4.6.

ST773

handle assy

6/6/03

3/8” Locking Nut

Handle Stub

Figure 4.7

- Insert handle stub into hole in front. Secure with 3/8”

locking nut.

ST1126

install stove front

Engage steel tabs behind

the cast iron bosses

Bottom tabs engage

notch in the leg

Figure 4.8

- Install the - front plate.

PILOT

ADJ

TPTH

ST228

attach switch

wires to valve

12/99

Figure 4.6

- Attach switch wires to valve (Millivolt).

Install the Stove Front

Insert the handle stub into the hole in the front casting.

Fasten in place with the 3/8” locking nut provided, Figure

4.7.
The front attaches to the stove by four steel tabs that

engage with corresponding cast ribs onto the sides and

bottom of the stove body. Position the front about 3” down

from stove top and lift the plate to engage the upper tabs

behind the adjacent ribs on the sides, Figure 4.8. Then

lower the front into position, so the lower tabs engage with

the corresponding ribs at the bottom.
When properly installed, the bottom of the stove front cannot

be pulled away from the sides without also lifting it.

Содержание OXDV30-IPI























































Результаты поиска

Содержание OXDV30-IPI

Отзывы:

Hearth & Home OXDV30-IPI, Инструкция по установке и эксплуатации, Страница: 26 / 54

Результаты поиска

Содержание OXDV30-IPI

Отзывы: