Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 20

Страница: 20 / 54

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

Vertical Through-The-Roof Application/Installation:

Note:

Refer to Figures 2.8 thru 2.10 for restrictor plate

adjustments for vertical vent runs.
This gas stove has been approved for:

• Vertical installations up to 40 feet (12 m) in height. Up to

a 10 feet (3 m) horizontal vent run can be installed within

the vent system using a maximum of two 90° elbows,

Figure 3.17.

• Up to two 45° elbows may be used within the horizontal

run. For each 45° elbow used on the horizontal plane,

the maximum horizontal length must be reduced by 18"

(450 mm).

Example:

Maximum horizontal length:

No elbows

= 10' (3 m)

1 x 45° elbow = 8.5' (2.6 m)

2 x 45° elbows = 7' (2.1 m)

• A minimum of an 8 feet (2.5 m) vertical rise is required,

Figure 3.17.

• Two sets of 45° elbow offsets may be used within the

vertical sections. From 0 to a maximum of 8 feet (2.5 m)

of vent pipe can be used between elbows, Figure 3.17.

• SLP-HVS supports offsets. This application will require

that you first determine the roof pitch and use the

appropriate starter kit. (Refer to Venting Components

list.)

• The maximum angular variation allowed in the system is

270°, Figure 3.18

• For the minimum height of the vent above the highest

point of penetration through the roof, Figure 3.18.

ST653

install snorkel

4/20/01 djt

RADIANCE

Waterproof Seal

Around Pipe

Firestop

Window Well

Drain

4" Clearance

Snorkel

Termination Cap

Wall Screws

and Anchors

Gravel

Figure 3.16

- Snorkel kit installation.

Figure 3.17 -

Typical Vertical Venting Configuration

ST933

Selkirk vertical venting

6/07

Ceiling Support Collar

Ceiling

Support

Plate

Trim Plate

Firestop

Spacer

Offset

Support Collar

Flashing

Storm Collar

Vertical Termination

Содержание OXDV30-IPI























































Результаты поиска

Содержание OXDV30-IPI

Отзывы:

Hearth & Home OXDV30-IPI, Инструкция по установке и эксплуатации, Страница: 20 / 54

Результаты поиска

Содержание OXDV30-IPI

Отзывы: