Hearth & Home OXDV30-IPI Скачать руководство пользователя страница 18

Страница: 18 / 54

3-90-30007480

Hearth and Home Technolgies • Oxford Direct/Natural Vent Installation Manual_R3 • 02/19

Divert Roof Run-off

HHT recommends, where excessive water run-off is possible,

use of one of the two options shown in Figure 3.10 to prevent

water running off the roof and onto/into the horizontal

termination cap.

4. Using appropriate length of pipe section(s) attach to

stove by twisting collar.

5. Measure the horizontal length requirement including a 2”

(51 mm) overlap, i.e. from the elbow to the outside wall

face plus 2” (51 mm) (or the distance required if installing

a second 90° elbow), Figure 3.13.

NOTE:

Always install vertical side wall horizontal venting

with a 1/4” rise for every 12” of run.

2. Secure firestop to the inside frame, center in the 9" x 9"

vent opening.

3. Place stove into position. Measure the vertical height (X)

required from the base of the flue collars to the center of

the wall opening, Figure 3.12

Vertical Side Wall Installation:
NOTE: Refer to Figures 2.8 thru 2.10 for restrictor plate

adjustments for vertical vent runs.

1. Locate vent opening on the wall. It may be necessary

to first position the stove and measure to obtain hole

location. Depending on whether the wall is combustible

or noncombustible, cut opening to size, Figure

3.11 (For combustible walls first frame in opening.)

Combustible Walls: Cut a 9" H x 9" W (244 x 244 mm) hole

through the exterior wall and frame as shown, Figure 30.

Noncombustible Walls: Hole opening must be 7" (178

mm) in diameter.

NOTE: When using flex vent, the opening will have to

be measured according to the 1/2” (13 mm) rise in 12”

(305 mm) vent run.

Install gutter

Install L-shaped

diverter

Figure 3.10

- Locate Vent Opening on Wall

Vent Opening for Combustible Walls

VO584-100
Vent Opening
2/99 djt

Stove Hearth

Framing Detail

Opening for Noncombustible Wall

(190 mm)

Stove Hearth

(244 mm)

Figure 3.11

- Locate Vent Opening on Wall

Figure 3.12

- Vertical Height Requirements

Содержание OXDV30-IPI























































Результаты поиска

Содержание OXDV30-IPI

Отзывы:

Hearth & Home OXDV30-IPI, Инструкция по установке и эксплуатации, Страница: 18 / 54

Результаты поиска

Содержание OXDV30-IPI

Отзывы: