Hearth and Home Technologies Quadra-Fire PS35-C, Руководство пользователя по эксплуатации и уходу

Страница: 28 / 40

28 04/21 7058-805F
6
Reference Materials
2. Convection Blower
The convection blower is mounted at the bottom rear of
the appliance. There are 2 impellers, one on each side
of the motor. The convection blower pushes heated air
through the heat exchange system into the room.
3. Exhaust Blower
The exhaust blower is mounted on the right side of the
appliance. The exhaust blower is designed to pull the
exhaust from the appliance and push it out through the
venting system.
4. Feed System
The feed system is located on the right side of the
appliance and can be removed as an entire assembly.
The assembly includes the feed motor, mounting
bracket, bearing and feed spring (auger). The hollow
feed spring (auger) pulls pellets up the feed tube from
the hopper area and drops them down the feed chute
into the fire pot.
5. Fire pot
The fire pot is made of high quality ductile iron and has
a cleaning pull-out rod. The floor of the fire pot opens
for cleaning when you pull out the rod. Be sure that
the floor returns to a completely closed position or your
appliance will not operate properly.
6. Fuse
The fuse is located on the side of the junction box
above to the red call light. The fuse will blow should a
short occur and shut off power to the appliance.
7. Heat Output Switch
The heat output switch is located on the upper right
back panel. The function of the heat output switch is to
regulate the burn rates; low, medium and high settings.
8. Hopper Switch
The hopper switch is located in the upper right hand
corner of the hopper. This switch is designed to shut
down the feed motor whenever the hopper lid is
opened.
9. Igniter
The igniter is mounted on the base of the fire pot.
Combustion air travels over the red hot igniter creating
super heated air that ignites the pellets.
10. Junction Box And Wiring Harness
The junction box is located on the lower left side of the
appliance, behind the left side panel. The junction box
and wiring harness are replaced as one component.
When describing the location of a
component, it is always AS YOU FACE THE
FRONT OF THE APPLIANCE.
A. Component Functions
1. Control Box
a.
The control box is located on the lower left side of
the appliance, behind the lower left side panel and
above the junction box.
b.
There is a light located inside of the control box.
The internal light will turn green when the appliance
has reached a temperature of 200°F (93°C) in
the fire pot. and will turn red when it reaches
600°F (315°C).
c. There is also an internal blue light located in the
control box. When you plug in the appliance the
blue light will automatically start blinking. For this
model, the blue light should flash 7 times every 10
seconds for the first 60 seconds after power up.
To set your control board on the correct number:
• Unplug the appliance.
•
Using #2 Phillips screw driver, 3/8” wrench, or 3/8”
socket loosen the three screws that hold the right upper
and lower side panels in place. You do not need to
remove the screws. Remove side panels by lifting up
and out.
•
Use a #2 Phillips screw driver to remove the control
box retainer bracket and lift control box out of the
junction box.
•
Using a ¼ inch flat head screw driver turn the rotary
switch until the desired number is showing on the dial.
• Re install control box and plug in appliance.
•
To confirm your selection is correct count the number of
times the blue light flashes.
Example:
If you are on setting 2 the control box will flash 2
times every 10 seconds for 1 minute.
Your PS35-C is set to #7 (7 flashes)
(Figure 28.1) .
E
NOTE:
Do NOT open the control box. This will void the
warranty. If you need to plug in or remove the
control box you must first unplug the appliance.
Figure 28.1 - Rotary Switch
Screwdriver
Slot