WIRELESS SPEAKER
HRSP 5040
VIBE
8092990
INSTRUCTION MANUAL
WHAT’S INCLUDED:
•
Speaker
•
USB C charging cable
•
3.5mm audio cable
•
Instruction Manual
The Bluetooth
®
word mark and logos are registered trademarks owned by Bluetooth
®
SIG, Inc. and any use of such marks by The Source (Bell) Electronics Inc. is
under license. Other trademarks and trade names are those of their respective owners.
COMPONENT IDENTIFICATION
1.
Power button
2.
Play/Pause
3.
Volume controls
4.
Line in port
5.
Charging indicator
6.
Charging port
PRODUCT OVERVIEW
You can use this item with any compatible, Bluetooth
®
-enabled device to stream music and
enjoy hands-free calling. Please read this manual first before using.
This speaker has an IPX6 rating: protected against high-pressure water jets from all
directions.
OPERATION
TO
DO THIS
Play/pause
Press the button to play, press again
to resume.
Next track
Press and hold the
button for 2
seconds.
Previous track
Press and hold the
—
button for 2
seconds.
Increase volume
S
h
ort Press the + button.
Decrease volume
Short Press the - button.
Answer/ End the call
Press the HR button
Reject the call
Press and hold the HR Button for 2
second
TWS
Press +and
–
button at the same times
and hold for 2 seconds
Reset
Press HR and
–
button at the same times
and hold for 2 seconds
STATUS INDICATOR
Mode indicator
Rapidly flashing blue
Pairing mode
Steady blue
Paired
Steady red
Line in mode
Charge indicator
Steady red
Charging
Steady green
Fully charged
CHARGING
Use the included charging cable to fully charge the speaker before first use. It will take
approximately 4 hours to fully charge.
•
The red LED will be ON while the speaker is charging
•
The red LED will turn green once charging is complete
Tip:
When the battery is low, the speaker will beep every few seconds, please charge the
speaker. If it is not plugged in to charge within approximately 15 minutes, it will turn OFF.
PAIRING
1.
Press and hold the
button to turn the speaker ON. The blue LED will flash.
2.
Turn Bluetooth
®
ON in your device settings and select
“HRSP
5040”.
3.
Once paired successfully, the blue LED will be ON and the speaker will chime.
4.
If you fail to pair your device or you want to pair it with a new device, please repeat the
steps outlined above.
NOTE: If there is no device paired within 10 minutes the speaker will turn OFF. To un-pair,
press the button or disconnect in your device settings.
NOTE: The speaker will automatically pair with previously paired devices provided the
Bluetooth
®
is ON and within range. The speaker will chime to indicate that it has been
successfully re-paired.
HANDSFREE SPEAKERPHONE
When a smartphone is connected to your speaker follow the steps below to take calls
handsfree.
1.
If there is an incoming call while streaming music, the speaker will ring for iOS ring tone or
beep for Android
TM
.
2.
Press the Play/Pause button to answer the call.
3.
Press the Play/Pause again to end the call.
LINE-IN (AUX IN) MODE
1.
Use the supplied cable to connect the speaker directly with your device.
2.
The LED will blink slowly.
Tip:
LINE-IN will take priority over the Bluetooth
®
connection.
TWS (TRUE WIRELESS STEREO) CONNECTION
Connect two 8092990 speakers for a true wireless stereo experience. To connect:
1.
Ensure neither speaker is connected to your device via Bluetooth and turn Bluetooth OFF
on your device.
2.
Press and hold the button on both speakers to turn ON. The button on both
speakers will flash.
3.
On either of speakers, press and hold “+”and “
-
” button at the same time for about 2 or 3
seconds until a prompt is heard. Another prompt will be heard in 2 seconds. It represents
TWS connected successfully.
4.
Turn Bluetooth® ON in your device settings and select “HRSP 5040” for Bluetooth pairing.
5.
When you hear the prompt and both button LED stay ON, Bluetooth connection to your
device is completed successfully.
Note: During your device under BT connection with TWS modes in use, you can press both
and
“+” buttons at the same time
for 3 seconds to clear all the pairing records.
TECHNICAL SPECIFICATIONS
Carrier Frequency:
Bluetooth
®
Battery Capacity:
3.7V, 2200mAh
Charging time:
2-3 hours
Frequency Response: 80HZ-18KHZ
Operation Distance:
Up to 10 meters/33 feet
TWS Distance:
3.5metres/11.5 feet
Output Power:
4W*2 (Max)
Play time:
12 hours
NOTE:
This speaker is in compliance with the specified Bluetooth
®
version. It does not
guarantee compatibility with all the functions on every Bluetooth
®
enabled device. Please
check your mobile
phone’s
user manual for compatibility and functionality.
TROUBLESHOOTING
No Sound:
•
Ensure the speaker is charged and has enough battery power for operation
•
Ensure the speaker is switched ON
•
Ensure Bluetooth
®
device is ON
•
The volume of the speaker is too low, adjust the volume to an appropriate level
NOTE:
•
If the speaker beeps every few seconds, the battery is low. Please recharge the
speaker.
•
When using the HR Speaker for your Personal computer.
•
Select playback device
“HRSP 5040 Stereo” for music listening
•
Select playback device
“HRSP 5040 Hands
-
Free AG Audio” when calling is
coming. check the volume when the call is coming. A
lso
please test the
speaker levels before using as speaker phone.
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—
Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
