Thank you for purchasing this product. For optimum performance and
safety, please read the instructions carefully and keep the manual for
future reference.
Please read below safety instructions carefully before installation and
operation:
1. Please pay attention to all the warnings and hints on this device.
2. Do not expose this unit to rain, moisture and liquid.
3. Do not put any stuff into the device.
4. Do not repair or open this device without professional people's
guidance.
5. Shut off power and make sure environment is safe before installation.
6. Do not plug-in/out the connected cables when it is in using.
rd
7. Make sure the specification matched if using 3 party DC adapters.
·
Introduction
·
Package Contents
TX
S
ender
x
1pc
RX Receiver
x
1pc
IR blaster extension
cable
x2
pcs
IR receiver extension
cable
x2
pcs
User manual
x
1pc
·
Installation Requirements
1
.
HDMI source devices: with HDMI OUTPUT interface, DVD, PS3, STB,
PC etc.
2. Display devices: With HDMI INPUT port, SDTV, HDTV, projector
3. Network cables
：
UTP/STP Cat6/Cat6A/Cat7 network cables, which following
the standard of IEEE-568B.
·
Panel
D
escription
1
.
TX Sender
Power input
Transmission
signal indicator
Connect with DC12V/1A power adapter
1. LED 1: It turns on when power on.
2. LED 2:
It turns on when the transmitter unit and the
receiver unit connect well with each other, and it
flashes when there is no transmission between
the transmitter unit and the receiver unit.
3. LED 3:
It flashes when the receiver unit connected well
with the HDMI display device, and it turns off
when no transmission between the receiver unit
and the display device.
2
. RX Receiver
·
Installation Procedures
1
.
To make a Cat6/6A/7 network cable
Follow the standard of IEEE-568B:
①
②
③
④
⑤
⑥
⑦
⑧
IR blaster extension
cable interface
Connect with IR blaster extension cable. Please put
the IR blaster close to source device to best transmit
the IR signal from receiver
⑧
Connect with IR receiver extension cable. Please
make sure the remote control is within the required
range of IR receiver
This HDBaseT 2.0 single network cable extender transmits HDMI signal
up to 100 meters over cat6 fluently and clearly. It is lossless in signal and
supports 3D, 24bits deep color, CEC, HDCP and ultra HD 4KX2K@60Hz.
It's a perfect solution for audio
＆
video transmission
in applications of
HD conference system, HD multimedia education system, HD digital
advertising and signage etc.
·
Features
1. Support bi-directional IR pass back.
2. Uncompressed HDMI video signal.
3. Supported resolution is up to ultra HD 4Kx2K@60Hz.
4. Support bi-directional RS232 passback.
5. Support HDBaseT 2 .0, HDCP 2.2, CEC, 24 deep color.
6. Support LPCM, DTS-HD and Dolby True HD audio.
7. Transmit 4Kx2K@60Hz signal over cat6 up to 100 meters.
HDBT Output
RS232
To connect with receiver by network cable
RS232 control
HDMI input
Reset button
Press for restarting the unit
Connect with HDMI source device
IR receiver extension
cable interface
①
②
③
④
⑤
⑥
⑦
⑧
RS232 serial port
cap ×2pcs
DC12V/
1
A
x2
pcs
Power input
Transmission
signal indicator
HDBT input
HDMI output
Connect with DC
12
V
1
A power adapter
1. LED 1: It turns on when power on.
2. LED 2:
It turns on when the transmitter unit and the
receiver unit connect well with each other, and it
flashes when there is no transmission between
the transmitter unit and the receiver unit.
3. LED 3:
It flashes when the receiver unit connected well
with the HDMI display device, and it turns off
when no transmission between the receiver unit
and the display device.
Connect with transmitter by network cable
Connect with HDMI display device
Reset button
Press for restarting the unit
RS232
RS232 control
IR receiver extension
cable interface
IR blaster extension
cable interface
⑧
Connect with IR receiver extension cable. Please
make sure the remote control is within the required
range of IR receiver
Connect with IR blaster extension cable. Please put
the IR blaster close to source device to best
transmit the IR signal from receiver
