background image

8

NOTICE

1.  When adjusting the signal level on the Receiving unit, please dial the rotary control switch from MIN to MAX 

and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level 
setting may cause overpowering issue that would shorten the product life significantly!

2.  Wrongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in the failure of the IR 

extenders. Please check carefully before plugging in the IR extender to the respective IR sockets.

3.  If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide 

DVI or HDMI display EDID information.

4.  All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and 

ASTRODESIGN Video Signal Generator VG-859C & VG-870B.

5.  The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type of HDMI sources, and 

the type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m [1,000ft] bulk 
cables) can transmit a lot longer signals than stranded UTP cables (usually in the form of fixed length patch 
cords). Shielded STP cables are better suited than unshielded UTP cables. A solid UTP Cat-5e cable shows longer 
transmission range than stranded STP Cat-6 cable. For long extension applications, solid UTP/STP cables are the 
only viable choice.

6.  EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance.
7.  To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable, one can use 

shielded STP cables to improve EMI problems, which is worsen in long transmission.

8.  Because the quality of the CAT5/6 cables has the major effect on how long the transmission limit can achieve 

and how good is the received picture quality, the actual transmission range is subject to one's choice of Cat-
5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is recommended.

9.  If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input [HDMI input #1] generally 

can produce better transmission performance among all HDMI inputs.

Performance Guide for HDMI over Category Cable Transmission

Performance rating

Type of category

 

cable

Wiring

Shielding

CAT5

CAT5e

CAT6

Solid

Unshielded (UTP)







Shielded (STP)







Stranded

Unshielded (UTP)





Shielded (STP)



Termination

Please use EIA/TIA-568-B termination (T568B) at any time

Содержание HDMI-C5IRB












Отзывы: