HCO UOvision UM562 Wireless Camera
SETUP INSTRUCTIONS
CAMERA SETUP
1. Confirm the power switch is at OFF position. Load 12AA
(recommended) or 4/8 AA (emergency) fully charged AA
batteries correctly according to the marks on battery slot.
Or connect 6V external power supply.
2. Insert the SD card correctly according to the mark on the
camera (16GB or smaller) and SIM card. Be sure that
the PIN of the SIM card is disabled. (You can disable the
PIN of a SIM card via your service provider.)
3. Slide the power switch to the SETUP position to set up
the camera. (Note: When going into the setup mode,
allow approximately 10-20 seconds for the camera to
acquire a signal. You will know it has acquired a signal
when six numbers or the carrier initials appear at the top
right of the view screen.)
4.
Press the “MENU” button to enter into the program menu,
then press the UP or DOWN arrow buttons to change
the items you want to change and RIGHT and LEFT
arrows to change the parameter settings. Press the OK
button to save parameter settings. Press the RIGHT and
LEFT arrows to change tabs when the tabs are
highlighted.
CAM tab:
Camera Mode:
Choose Photo or Video.
Photo Size:
Choose the image size, e.g. 5MP, 8MP or
3MP.
Photo Burst:
Choose the continuous shooting numbers
after each triggering.
Video Size (video mode):
Choose the video size
Video Length (video mode):
Set the video length to
desired setting.
PIR tab:
Sensitivity:
High, Low, and Normal setting available.
Time Lapse:
The camera can be set to record/capture
at a certain time of the day as of requested. While Time
Lapse is set to Off, the camera works only by PIR
triggering.
Start-Stop:
Start-
Stop “On” means that the camera
works by PIR triggering; Start-
Stop “Off” means that the
camera PIR stops working.
GSM
Send Mode:
There are 3 MMS mode: Daily report,
Instant and OFF.
Send Via:
MMS and GPRS selectable
Send To:
Enter the phone number or email where the
MMS is to be sent.
Recipients:
Press
“
Enter
”
to review what you have
set to receive the MMS or GPRS pictures.
Location:
Press enter to get the Longitude & Latitude
information.(show only in the display screen)
Download Tool:
Please refer to the Guide on GSM
Setup for details.
SYS tab:
Set Clock:
Enter to set the Date and Time
Time Stamp:
Choose "On" or "Off" to show the time on
the picture or to remove.
Flash Range:
Infrared Flash range: .30 ft. /9m
Password:
The default password is 0000. Choose OFF
to stop this function.
Language:
English
（
Preset
）
we provide the choice for
customer to choose the language, please contact your
distributor for assistance.
Beep:
Customer can choose ON/OFF when operating
the cameras.
Overwrite:
ON/OFF, if choosing “ON” The camera
writes off the previous taken pictures and continues to
record new pictures/videos, thus, the SD-card is
recyclable, customer needs not to change SD card
frequently.
Default Set:
Restore all customer settings to default
values.
Format:
Format the SD-card.
5. Place the camera at the target area and turn on the
camera
(
slide the power switch to ON), the camera will
take pictures or videos as preset in step 4.
6. In live preview screen, press
button to manually
capture photos or record a video.
7. Press
button to playback the pictures. Use the UP or
DOWN arrow buttons to scroll through pictures on the
color monitor.
8. To delete an image in SETUP mode, press
button to
show the image, and then press DELETE to delete an
image.
GSM SETUP
1. Insert a SD card and a SIM card into the camera.
2. Switch the camera to SETUP position, press MENU.
3. Go to the GSM tab. Change the send mode to Instant.
Wait until the camera acquires a signal when six
numbers or the carrier initials appear on the screen.
4. Scroll down to Download Tool. Press OK to download
the GSMSETUP.ZIP into the SD card.
5. Turn off the camera. Remove the SD card from the
camera and put in the computer.
.
