HBM GEN3i Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 1160

HBM GEN3i Скачать руководство пользователя страница 86

6.5

Signal conditioning

GEN3i supports common analog sensors with the highest performance signal
conditioning available. All inputs are sampled simultaneously for exact time
correlation, and the front ends deliver a typical maximum static error of 0.1%.

Plug

-

and

-

play hardware discovery with scalability to any number of channels.

Perception software can group and outline similar amplifiers for one

-

click

settings. Extensive diagnostics gives the confidence of correctly wired and
working sensors before any test.

GEN3i

86

I3763-3.1 en HBM: public

«
...
84
85
86
87
88
...
»

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов