HBM GEN3i Скачать руководство пользователя страница 856 | Manualshive

Страница: 856 / 1160

background image

E.5

Recovery partition creation

To create/restore the recovery partition, a USB disk/stick with a back

-

up copy

of the recovery partition is required. If this back

-

up copy has not been made or

is lost, a copy can be ordered from HBM service.

E.5.1

Using the Integrated System Recovery USB Disk
1

Power off the mainframe.

2

Connect the mouse and keyboard.

3

Insert the USB disk in one of the USB 2.0 ports (The USB3.0 ports will not
allow the restore process to finish correctly).

4

Power on the system and keep the

F7

function key pressed until the

following dialog appears.

Figure E.40:

Listed boot devices

A

Name of installed Solid State Drive

B

Name of USB disk/stick attached to your system

If the attached USB disk/stick does not appear, it was installed the system
was powered on or the USB disk/stick is not bootable. Correct the issue,
power off the system and restart from the beginning.

Use the arrow keys to select the USB disk/stick in the list of boot devices
and press enter. The system will boot the recovery partition creation.

A disk partition inspection is started.

l

If a recovery partition is detected, the

Recovery Partition Restore

is

started. For more information, please refer to "Starting recovery partition
restore" on page 858.

l

If the Recovery partition is not detected, the

Recovery Partition

Creation

is started. For more information, please refer to "Starting recovery

partition creation" on page 857.

GEN3i

856

I3763-3.1 en HBM: public

«
...
854
855
856
857
858
...
»

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GEN3i

Бренд: Davis Instruments Страницы: 16

Бренд: Watlow Страницы: 214

Бренд: Hobo Страницы: 11

Бренд: Dostmann Electronic Страницы: 14

Бренд: I.Trek Страницы: 17

Бренд: M2MLogger Страницы: 18

Бренд: Fimer Страницы: 29

Бренд: Race Technology Страницы: 45

Бренд: Madge Networks Страницы: 16

Бренд: Ebro Страницы: 40

Бренд: Omega Engineering Страницы: 6

Бренд: Datafox Страницы: 184

OM-CP-PRHTEMP2000

Бренд: Omega Страницы: 5

GrowControl SXC

Бренд: Agrowtek Страницы: 10

Бренд: SolarMax Страницы: 76

Бренд: Bosch Страницы: 199

Бренд: Steren Страницы: 3

Бренд: Steren Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды