HBM GEN3i Скачать руководство пользователя страница 418

Страница: 418 / 1160

A.4

B2639–2.1 en (GEN series GN411)

Capabilities Overview

Model

GN411

Maximum sample rate per channel

1 MS/s

Memory per card

512 MB

Analog channels

Anti

alias filters

Fixed bandwidth analog AA

filter combined with sample rate tracking digital AA

filter

ADC resolution

16 bit

Isolation

Channel to channel and channel to chassis

Input type

Analog, isolated balanced differential

Passive voltage/current probes

Not supported

Sensors

Quarter, half and full bridges using either voltage or current excitation.
Force, Pressure, MEMS

type Accelerometers and Potentiometric Displacement and other

strain gauge bridge sensors using either voltage or current excitation

TEDS

Not supported

Real

time cycle based calculators

Not supported

Real

time formula database calculators (option)

Not supported

EtherCat

output

Not supported

Digital Event/Timer/Counter

Not supported

Standard data streaming (up to 200 MB/s)

Supported

Fast data streaming (up to 1 GB/s)

Not supported

Slot width

GEN3i

418

I3763-3.1 en HBM: public

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GEN3i

Отзывы:

HBM GEN3i, Руководство пользователя, Страница: 418 / 1160

Результаты поиска

Содержание GEN3i

Отзывы: