HBM GEN3i Скачать руководство пользователя страница 258

Страница: 258 / 1160

Bridge completion

full (4/4) bridge

A full bridge type sensor is a sensor that has all four bridge resistors on

board;

no completion is required.

+V_EXC

−V_EXC

+AMP INPUT

−AMP INPUT

BRIDGE RESISTOR

BRIDGE COMPLETION

Figure 12.40:

Full

bridge layout

At least four wires are necessary to connect a bridge such as this. Please refer
to Figure 12.37 for connection details. Inform the Perception software when a
full bridge is used.

To select full bridge completion in Perception

To select full bridge completion, proceed as follows:

In Perception, go to the

Settings

sheet.

In the task pane, select the

Bridge

in the

Input

section.

Select one or more channels.

GEN3i

258

I3763-3.1 en HBM: public

Содержание GEN3i









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание GEN3i

Отзывы:

HBM GEN3i, Руководство пользователя, Страница: 258 / 1160

Результаты поиска

Содержание GEN3i

Отзывы: