HB-THERM CLEAN-5 Скачать руководство пользователя страница 33

Страница: 33 / 97

HB-CL2

Cleaning Unit

Transport, packing and storage

O8305-EN 2022-01

5.3 Transport inspection

Check the delivery immediately on receipt for completeness and
transport damage.

If externally detectable transport damage is found, proceed as
follows:



Do not accept the delivery, or only with reservation.



Record the extent of transport damage in the transport

documents or on the delivery note of the forwarding agent.



Start complaints procedure.

NOTE!

Claim any damage as soon as it is detected.
Compensation claims can only be submitted within
the applicable complaints periods.

5.4 Packing

Fig. 8: Packaging

The unit is packed corresponding to the expected transport
conditions on a wooden pallet, secured with a polypropylene strap
and wrapped in stretch film.

Only environmentally compatible materials have been used for the
packaging.

The packaging should protect the individual components from
transport damage, corrosion and other damage. Therefore, do not
destroy the packaging.

Handling packing materials

If there is no returns agreement for the packing, separate materials
according to type and size and direct to further use or recycling.

ATTENTION!
Environmental damage caused by incorrect
waste disposal!

Packing materials are valuable raw materials and
can continue to be used in many cases or sensibly
reconditioned and recycled.

Therefore:

– Dispose of packing materials environmentally.
– Follow the locally valid waste disposal

regulations. If necessary employ a special
waste disposal company to dispose of packing
material.

Содержание CLEAN-5


































































































Результаты поиска

Содержание CLEAN-5

Отзывы:

Похожие инструкции для CLEAN-5

Бренды по названию

Популярные бренды

HB-THERM CLEAN-5, Инструкция по эксплуатации

Результаты поиска

Содержание CLEAN-5

Отзывы:

Похожие инструкции для CLEAN-5

Бренды по названию

Популярные бренды