Hawkeye Mfg AGCO RoGator A Series Скачать руководство пользователя

Страница: 45 / 54

CHAPTER

Sidekick Pro™ ICD Installation: Connecting Sidekick PRO ICD Direct Injection Pumps to the ISOBUS

CHAPTER 7

SIDEKICK PRO™ ICD

INSTALLATION

CONNECTING SIDEKICK PRO ICD DIRECT INJECTION PUMPS TO THE

ISOBUS

Sidekick Pro direct injection pumps installed by AGCO are Raven CAN version and are connected to the CANbus.

To work with the Hawkeye® 2 Product Control System, change the pumps to Sidekick Pro ICD pumps and connect

them to the machine’s ISOBUS using a Raven adapter cable (P/N 115-0172-325). Contact a local Raven dealer to

order this cable and ICD pumps if necessary.

NOTE:

If adding a new injection system to the machine, also order the required AGCO cable harness from

your local AGCO dealer.

1. Inspect the Sidekick Pro label to determine if it is the ICD version. The label will either read Raven Sidekick Pro™

ICD and the part number will be one of the following:

•

P/N: 1-063-0173-768 (1-40 oz/min pump)

•

P/N: 1-063-0173-769 (5-200 oz/min pump)

FIGURE 1. Raven Sidekick Pro ICD Label

2. Remove the cover of the ECU cabinet that contains the product control ECU’s on the middle of the right frame

rail. Refer to Figure 1, “RoGator ECU Cabinet Location,” on page 25.

3. Locate the RoGator ISOBUS Tee Cable (P/N 115-0172-325). This may have been provided with your Hawkeye® 2

system kit, or it may need to be ordered.

4. Remove the 4-Pin to 3-Pin Deutsch adapter cable with ISOBUS Terminator and set aside. This will be used in a

later step.

5. Follow the cable from the injection pumps down the frame rail to the round bulkhead connector on the back of

the ECU cabinet. This is typically the bulkhead connector furthest towards the front of the machine on the ECU

cabinet.

6. Locate the mating bulkhead connector on the inside of the ECU cabinet.
7. Identify and disconnect the green/yellow twisted wires from the identified bulkhead connector that lead to a 4-

pin Deutsch connector in the ECU cabinet.

8. Connect the 4-pin Deutsch receptacle coming from the bulkhead connector to the mating 4-pin plug on the

ISOBUS adapter tee (P/N 115-0172-325) where the adapter and terminator were removed.

9. Locate and disconnect the square Raven passive terminator on the cable harness near the Sidekick Pro Injection

Pumps.

Содержание AGCO RoGator A Series






















































Результаты поиска

Содержание AGCO RoGator A Series

Отзывы:

Похожие инструкции для AGCO RoGator A Series

Бренды по названию

Популярные бренды

Hawkeye Mfg AGCO RoGator A Series, Руководство по установке

Результаты поиска

Содержание AGCO RoGator A Series

Отзывы:

Похожие инструкции для AGCO RoGator A Series

Бренды по названию

Популярные бренды