HAWEKA AXIS 500 Скачать руководство пользователя страница 39

Страница: 39 / 52

Wheel Alignment AXIS500

AXIS500 Manual Instructions

9 Adjustment by Run-out compensation

Preparations

In order to change the magnetic feet for the

runout

compensation

adaptors

recommended to put the measuring head onto

the mounting stand. Loosen the fastening

screws and change the 3 magnetic feet for the

3 compensation adapters. Tighten the adapters

only insofar as you can still move them in the

longitudinal slots of the 3-arm-star. Leave a

play (min. 1 revolution) while fastening knurled

screw of adapter.

Now the grab arms are attached to the grab

arm assembly. The measuring head is centrally

mounted onto the rim by shifting the adaptors

until they correspond to the rim flange

diameter. Illustration 36 shows how the adaptor

feet have to be attached to the rim flange: the

feet are directed towards the wheel hub.

Mounting of complete assembled
measuring head to the rim

With its arms expanded, the measuring head is

first attached to the lower rim flange part. The

single upward arm is not attached yet, but only

moved towards the rim after the lower adaptors

are attached. During this process the adaptor is

shifted so that it presses against the rim flange.

The last locking device is then tightened.

Important:

The measuring head is still not

fixed to the rim. The grab arms are now

pressed into the first or second exterior profile

and the quick-clamping device is tightened until

the three adaptors are evenly attached to the

rim. Now the vehicle can be lifted until wheel is

enabled to be turned.

(

Illustration 37)

(

Illustration 35)

play of 1

revolution

optional accessory

(

Illustration 36)

Содержание AXIS 500





















































Результаты поиска

Содержание AXIS 500

Отзывы:

Бренды по названию

Популярные бренды

HAWEKA AXIS 500, Руководство по эксплуатации

Результаты поиска

Содержание AXIS 500

Отзывы:

Бренды по названию

Популярные бренды