HAUL MASTER 93747 Скачать руководство пользователя страница 5

Page 5

SKU 93747

For technical questions, please call 1-800-444-3353.

5.

Always check to make sure the payload being transported is properly and
safely secured in the Trailer.  
Load the Trailer evenly from side to side with 60%
of the load forward of the Axle.

6.

Prior to using the Trailer, make sure to read and understand all instructions
and safety precautions as outlined in the owner’s manual for the towing
vehicle.  
Make sure the towing vehicle is capable of towing the Trailer and its
payload.  Make sure the hitch on the towing vehicle is capable of towing the
Trailer and its payload.  The towing capacity of the hitch is typically stamped on
the hitch drawbar.

7.

Make sure the Coupler and the vehicle’s ball hitch (not included) are of
equal mating size (2”) and are rated equal to or greater than the weight of
the Trailer  and its payload.

8.

Do not exceed 55 miles per hour when towing the Trailer.  Excess speed is a
major cause of vehicle-trailer accidents.

9.

The Tail  Light Bulbs supplied with this Trailer are for a 12 volt DC electrical
system only.  
Do not attempt to power the Light Bulbs with any other type or
voltage electrical current.

10.

Whenever possible, park the Trailer on a flat, level, paved, surface and chock
both Tires to keep the Trailer from accidently moving.

11.

CAUTION!   Care must be taken when backing up the Trailer.  Only back

up the Trailer on a straight path.  If the Trailer is allowed to turn off the straight
path while backing up, the Trailer could jackknife, causing severe damage to the
Trailer and towing vehicle.

12.

Maintain labels and nameplates on the Trailer.   These carry important informa-
tion.  If unreadable or missing, contact Harbor Freight Tools for a replacement.

13.

Reporting safety defects:  If you believe your Trailer has a defect which could
cause a crash or could cause injury or death, you should immediately inform the
National Highway Traffic Safety Administration (NHTSA) in addition to notifying
the manufacturer, Changzhou Nanxiashu Tool Company.  If NHTSA receives
similar complaints, it may open an investigation, and if it finds that a safety defect
exists in a group of vehicles, it may order a recall and remedy campaign.  How-
ever, NHTSA cannot become involved in individual problems between you,
Harbor Freight Tools, or the manufacturer.  To contact NHTSA, you may either call
the Auto Safety Hotline toll-free at 1-800-424-9393 or 202-366-0123 or write
NHTSA, U.S. Department, 400 7th Street SW NSA-11, Washington, D.C. 20590.

Содержание 93747

























Отзывы: