background image

1

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including:

BEFORE BEGINNING INSTALLATION, READ THESE IMPORTANT SAFETY INSTRUCTIONS

E M E R G E N CY   L E D   D R I V E R 

I N S TA L L AT I O N   A N D   O P E R AT I N G 
I N S T R U C T I O N S

Note:

 Installation requires application of 

the Luminaire Modification Label provided 

in your kit, as per UL. This label states: “This 

equipment has more than one connection 

point.” This label must be applied to the fixture 

housing during installation.

SAVE THESE INSTRUCTIONS

Use with grounded, UL Listed, damp location rated fixtures.

WWW.HATCHLIGHTING.COM • 7821 W

OOdLANd

 C

eNTer

 B

Lvd

. T

AMpA

, FL 33614 • pH: 813.288.8006 • FX: 813.288.8105 • S

ALeS

@

HATCHLIGHTING

.

COM

 r

ev

: 07/28/2020

WARNING:

 Risk of fire or electric shock. Fixture wiring and 

electrical parts may be damaged when drilling for installation of LED 

Emergency Driver. Check for enclosed wiring and components.

WARNING:

 Risk of fire or electric shock. The LED Emergency Driver 

installation requires knowledge of luminaire electrical systems. If not 

qualified, do not attempt installation; contact a qualified electrician.

WARNING:

 Risk of fire or electric shock. The LED Emergency Driver 

is only for use with surface mount or recessed Type IC or Non-IC 

products listed to UL Standards. Suitable for use in damp locations 

and plenum spaces. Not for use in heated air outlets or hazardous 

locations.

WARNING:

 Risk of fire or electric shock. Do not alter, relocate or 

remove wiring, lamp holders, power supply or any other electrical 

component.

WARNING:

 To prevent wiring damage and abrasion, do not expose 

wiring to edges of sheet metal or other sharp objects.

WARNING:

 Do not make or alter any open holes in the wiring 

enclosure or electrical component enclosure during installation. 

Only the open holes indicated in the instructions may be added or 

altered as a result of installation. Do not leave any other open holes 

in the wiring enclosure or electrical component enclosure during 

installation.

CAUTION:

 Before installing, make certain the AC power to the 

fixture is off.

CAUTION:

 Confirm there is 120-277V at the fixture before 

beginning installation.

CAUTION:

  To prevent electrical shock, only mate the unit connector 

after the installation is complete and before the AC power to the 

fixture is back on.

CAUTION:

  This fixture provides more than one power supply 

output source. To prevent electrical shock, disconnect both normal 

and emergency sources by turning off the AC branch circuit and 

disconnecting the unit connector.

 

CAUTION:

 Do not look directly at the LED light source for extended 

periods of time to prevent harm to eyes.

CAUTION:

  This is a sealed unit.  Components are not replaceable.  

Replace entire unit when necessary.

CAUTION: 

 This Emergency LED Driver requires an unswitched AC 

power source of 120-277V, 50/60 Hz.  The AC LED driver MUST 

be on the same branch circuit as the Emergency LED driver. 

CAUTION:

 Verify that the LED load requirements match/are 

compatible with the emergency driver selected.

CAUTION:

 Do not use outdoors.

CAUTION:

 Do not mount near gas or electric heaters.

CAUTION:

 Install in accordance with the National Electrical Code 

and regulations

CAUTION:

 Do not mount in locations or at heights in which the 

emergency driver could be tampered with by unauthorized personnel.

CAUTION:

 Do not use this equipment for anything other than its 

intended use.

CAUTION:

 Do not use accessory equipment not recommended by 

the manufacturer as this may cause an unsafe condition.

CAUTION:

 Use with grounded, UL Listed, damp location rated 

fixtures.  Emergency Driver case should be grounded.

CAUTION:

  The equipment is intended for ordinary locations and for 

permanent installation into one or more Listed emergency luminaires.

The following are included:

ELP20-2060-UNV-SD

PARTS

QUANTITY

LED Emergency Driver 

1

Test Button

1

Tek Screws

2

Installation Guide

1

Luminaire Modification Label

1

Screw Wire Connectors

2

Wall Plate

1

Wall Plate Screws

2

Отзывы: