Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 276

Страница: 276 / 306

MAINTENANCE PRACTICES

61-00-15

Page 6-38

Rev. 24 Dec/20

Propeller Owner's Manual

115N

(12) Optionally, perform dynamic balancing in accordance

with the procedures and limitations specified in the

section, "Dynamic Balance" of this chapter.

8. Dynamic Balance

A. Overview
CAUTION 1: INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE PROPELLER

CRITICAL PARTS. REFER TO THE

INTRODUCTION CHAPTER OF THIS

MANUAL FOR INFORMATION ABOUT

PROPELLER CRITICAL PARTS. REFER TO

THE ILLUSTRATED PARTS LIST CHAPTER

OF THE APPLICABLE OVERHAUL

MANUAL(S) FOR THE IDENTIFICATION OF

SPECIFIC PROPELLER CRITICAL PARTS.

CAUTION 2: IF REFLECTIVE TAPE IS USED FOR

DYNAMIC BALANCING, DO NOT APPLY THE

TAPE ON EXPOSED BARE METAL OF THE

BLADE. THIS WILL ALLOW MOISTURE TO

COLLECT UNDER THE TAPE AND CAUSE

CORROSION THAT CAN PERMANENTLY

DAMAGE THE BLADE. REFLECTIVE TAPE

MUST BE REMOVED AFTER DYNAMIC

BALANCING IS COMPLETED.

NOTE: Dynamic balance is recommended to reduce

vibrations that may be caused by a rotating system

(propeller and engine) imbalance. Dynamic

balancing can help prolong the life of the propeller,

engine, airframe, and avionics.

(1) Dynamic balance is accomplished by using an accurate

means of measuring the amount and location of the

dynamic imbalance.

(2) The number of balance weights installed must not

exceed the limits specified in this chapter.

(3) Follow the dynamic balance equipment manufacturer’s

instructions for dynamic balance in addition to the

specifications of this section.

NOTE: Some engine manufacturers' instructions also

contain information on dynamic balance limits.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды