Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 203

Страница: 203 / 306

Propeller Owner’s Manual

115N

INSPECTION AND CHECK

61-00-15

Page 5-9

Rev. 24 Dec/20

B. Static RPM Check - for Reciprocating Applications ONLY

NOTE: This operational check should be performed after

installation, maintenance, or propeller adjustment.

CAUTION:

A CALIBRATED TACHOMETER MUST

BE USED TO MAKE SURE OF THE

ACCURACY OF THE RPM CHECK.

(1) Set the brakes and chock the aircraft or tie aircraft down.
(2) Back the Maximum RPM Stop on the governor out

one turn.

(3) Start the engine.
(4) Advance the propeller control lever to MAX (max RPM),

then retard the control lever one inch (25.4 mm).

(5) SLOWLY advance the throttle to the maximum manifold

pressure.

(6) Slowly advance the propeller control lever until the engine

speed stabilizes.
(a) If engine speed stabilizes at the maximum power

static RPM specified by the TC or STC holder, then

the low pitch stop is set correctly.

(b) If engine speed stabilizes above or below the rated

RPM, the low pitch stop may require adjustment.

Refer to the Maintenance Practices chapter of this

manual.

(7) Stop the engine.
(8) Return the Maximum RPM Stop on the governor to the

original position.

(9) Test fly the aircraft to confirm the maximum rated RPM

specified in the aircraft TC or STC is achieved.

(a) Adjust the governor to the rated RPM with the

Maximum RPM Stop screw.
1 If the governor is adjusted to the rated RPM

with the maximum RPM stop screw, hold the

maximum RPM stop screw in place and torque

the maximum RPM stop locking nut in accordance

with Table 3-2, Torque Table.

(10) Refer to the Aircraft Maintenance Manual for additional

procedures that may be required after propeller

installation.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды