Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 201

Страница: 201 / 306

Propeller Owner’s Manual

115N

INSPECTION AND CHECK

61-00-15

Page 5-7

Rev. 24 Dec/20

3. Operational Checks

CAUTION:

INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE PROPELLER

CRITICAL PARTS. REFER TO THE

INTRODUCTION CHAPTER OF THIS

MANUAL FOR INFORMATION ABOUT

PROPELLER CRITICAL PARTS. REFER TO

THE ILLUSTRATED PARTS LIST CHAPTER

OF THE APPLICABLE OVERHAUL MANUAL(S)

FOR THE IDENTIFICATION OF SPECIFIC

PROPELLER CRITICAL PARTS.

A. Initial Run-Up

(1)

Following propeller installation and before flight, perform

the Initial Run-Up procedure in accordance with the

instructions on this section.

WARNING:

REFER TO THE AIRCRAFT

MAINTENANCE MANUAL FOR

ADDITIONAL PROCEDURES THAT MAY

BE REQUIRED AFTER PROPELLER

INSTALLATION.

(2) Perform engine start and warm-up in accordance with

the Pilot’s Operating Handbook (POH).

CAUTION:

AIR TRAPPED IN THE PROPELLER

HYDRAULIC CYLINDER WILL CAUSE

PITCH CONTROL TO BE IMPRECISE AND

CAN CAUSE PROPELLER SURGING.

(3) Cycle the propeller control through the operating blade

range from low pitch (or reverse), to high pitch (or as

specified in the POH).

(a) Repeat this step at least three times.

NOTE: Cycling the propeller control purges air

from the propeller hydraulic system and

introduces warm oil to the cylinder.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды