Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 197

Страница: 197 / 306

Propeller Owner’s Manual

115N

INSPECTION AND CHECK

61-00-15

Page 5-3

Rev. 24 Dec/20

1. Pre-Flight Checks

(Rev. 2)

CAUTION:

INSTRUCTIONS AND PROCEDURES IN

THIS SECTION MAY INVOLVE PROPELLER

CRITICAL PARTS. REFER TO THE

INTRODUCTION CHAPTER OF THIS

MANUAL FOR INFORMATION ABOUT

PROPELLER CRITICAL PARTS. REFER TO

THE ILLUSTRATED PARTS LIST CHAPTER

OF THE APPLICABLE OVERHAUL MANUAL(S)

FOR THE IDENTIFICATION OF SPECIFIC

PROPELLER CRITICAL PARTS.

A. Important Information

(1) Follow propeller pre-

flight inspection procedure

pecified in the Pilot Operating Handbook (POH

) in

addition to the inspections

specified in this section.

(2) Defects or damage found during the pre-flight inspection

must be evaluated in accordance with the applicable

section in the Testing and Troubleshooting chapter

and/or the Maintenance Practices chapter of this

manual.

B. Propeller Blades

(1) Visually examine the entire blade (leading edge, trailing

edge, face, and camber sides) for nicks, gouges,

erosion, and cracks.
(a) Normal erosion (sand-blasted appearance) on the

leading edge of the blade is permitted and does not

require removal before further flight.

(2) Visually examine the blades for lightning strike

indications in accordance with the section, "Lightning

Strike" in this chapter.

(3) Check the blades for radial play or movement of the

blade tip (in-and-out, fore-and-aft, and end play).
(a) Refer to the section, “Loose Blades” in this chapter

for blade play limits.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды