Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 108

Страница: 108 / 306

Propeller Owner's Manual

115N

INSTALLATION AND REMOVAL

61-00-15

Page 3-14

Rev. 24 Dec/20

4. Bulkhead Installation

(Rev. 3)

A. General

(1) The spinner support must be mounted to the hub before

the propeller can be installed on the aircraft.

(2) The spinner assembly may be supplied with spinner

mounting hardware, including long hub clamping bolts,

washers, and nuts.
(a) If the propeller is shipped with longer hub clamping

bolts, spinner mounting hardware will not be

supplied with the spinner assembly. Refer to

Hartzell Propeller Inc. Application Guide Manual 159

(61-02-59) for the applicable installation.

(b) On some installations, it may be necessary to install

spacers and/or washers under the head of the hub

clamping bolt to avoid interference with the aircraft

cowling.
1 If the installation of the spinner mounting kit

requires removal of hub clamping bolts, the

propeller must be sent to certified propeller

repair station with the appropriate rating.

B. Installation of a Metal Bulkhead

CAUTION:

REMOVE THE NUTS AND WASHERS

FROM THE HUB CLAMPING BOLTS ON

THE LEFT/RIGHT SIDE OF THE BLADE

SHANK ONLY. DO NOT REMOVE THE

HUB CLAMPING BOLTS.

(1) Remove the nuts and washers from the hub clamping

bolts located on the left/right side of the blade shank.

Refer to Figure 3-3.
NOTE: Additional washers/spacers may have been

used during assembly of the propeller for

hub clamping purposes. These additional

washers/spacers may not be components of

the applicable spinner mounting kit.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды