Hartzell HC-C2YR-4CF/FC8475-6 Скачать руководство пользователя страница 100

Страница: 100 / 306

Propeller Owner's Manual

115N

INSTALLATION AND REMOVAL

61-00-15

Page 3-6

Rev. 24 Dec/20

2. Pre-Installation

A. Inspection of Shipping Package

(1) Examine the exterior of the shipping container, especially

the box ends around each blade, for signs of shipping

damage.
(a) If the box is damaged, contact the freight company

for a freight claim.

(b) A hole, tear or crushed appearance at the end of the

box (blade tips) may indicate that the propeller was

dropped during shipment, possibly damaging the

blades.
1 If the propeller is damaged, contact Hartzell

Propeller Inc. Refer to the section, “Hartzell

Propeller Inc. Contact Information” in the

Introduction chapter of this manual.

B. Uncrating

(1) Put

the propeller on a firm support.

(2) Remove the banding and any external wood bracing

from the cardboard shipping container.

(3) Remove the cardboard from the hub and blades.
CAUTION:

DO NOT STAND THE PROPELLER ON A

BLADE TIP.

(4) Put the propeller on a padded surface that supports the

entire length of the propeller.

(5) Remove the plastic dust cover cup from the propeller

mounting flange, if installed.

C. Inspection after Shipment

(1) After removing the propeller from the shipping container,

examine the propeller components for shipping damage.

Содержание HC-C2YR-4CF/FC8475-6



















































































































































































































































































































Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды

Hartzell HC-C2YR-4CF/FC8475-6, Руководство пользователя и журнал учета

Результаты поиска

Содержание HC-C2YR-4CF/FC8475-6

Отзывы:

Похожие инструкции для HC-C2YR-4CF/FC8475-6

Бренды по названию

Популярные бренды