Hartzell HC-82VF-1 Скачать руководство пользователя страница 7

Страница: 7 / 250

Propeller Owner's Manual

175

Page 5

Rev. 1 Jun/11

61-00-75

REVISION HIGHLIGHTS

REVISION HIGHLIGHTS:

Revision 1

, dated

June 2011

, incorporates the following:

•

Revised Cover, Revision Highlights, List of Effective Pages, and

Table of Contents to reflect changes

•

Service Documents List section

•

Added new Caution statements

•

Added Airworthiness Limitations section

• Introduction Chapter

•

Added information to explain the use of ( ) in a propeller model
designation

•

Revised information about ice-protection systems

•

Updated Reference Publications section

•

Added information about Hartzell Recommended Facilities

• Installation and Removal Chapter

•

Revised references about ice protection systems

• Clarified use of aviation grade reciprocating engine oil for

lubrication of felt dust seal

•

Testing and Troubleshooting Chapter

•

Add Static RPM Check to Operational Tests section

•

Relocated previous Propeller Equipment and Settings
information to the Maintenance Practices Chapter

•

Relocated Maximum RPM information from the Maintenance
Practices Chapter to the Testing and Troubleshooting chapter

• Inspection and Check Chapter

• Revised the Preflight Checks section
•

Revised the Operational Checks section

•

Revised Airworthiness Limitations section

•

Updated Long Term Storage Information

• Maintenance Practices Chapter

•

Added information about mixing Aeroshell greases 5 and 6

•

Updated the Painting After Repairs section

•

Added Caution and Warning to Blade Repairs section

•

Updated Dynamic Balance section

•

Relocated Propeller Equipment Settings information from
the Testing and Troubleshooting chapter to the Maintenance
Practices chapter

• Anti-Ice and De-Ice System Chapter

•

Updated reference information

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды