Hartzell HC-82VF-1 Скачать руководство пользователя

Страница: 37 / 250

Propeller Owner’s Manual

175

INTRODUCTION

61-00-75

Page 1-7

Rev. 1 Jun/11

(11) Propeller ice protection system components not supplied by

Hartzell Propeller Inc. are controlled by the applicable TC

or STC holder’s Instructions for Continued Airworthiness

(ICA).

CAUTION:

DO NOT USE OBSOLETE OR OUTDATED

INFORMATION. PERFORM ALL

INSPECTIONS OR WORK IN ACCORDANCE

WITH THE MOST RECENT REVISION OF

THIS MANUAL. INFORMATION CONTAINED

IN THIS MANUAL MAY BE SIGNIFICANTLY

CHANGED FROM EARLIER REVISIONS.

FAILURE TO COMPLY WITH THIS MANUAL

OR THE USE OF OBSOLETE INFORMATION

MAY CREATE AN UNSAFE CONDITION THAT

MAY RESULT IN DEATH, SERIOUS BODILY
INJURY, AND/OR SUBSTANTIAL PROPERTY

DAMAGE. FOR THE MOST RECENT

REVISION LEVEL OF THIS MANUAL, REFER

TO THE HARTZELL WEB SITE AT
WWW.HARTZELLPROP.COM.

(12) The information in this manual supersedes data in all

previously published revisions of this manual.

(13) The airframe manufacturer’s manuals should be used in

addition to the information in this manual due to possible

special requirements for specific aircraft applications.

) Approved corrosion protection followed by approved paint

must be applied to all aluminum blades.

(a)

For information concerning the application of corrosion

protection and paint, refer to the Maintenance Practices

chapter of this manual.

(b)

Operation of blades without the specified coatings and

finishes, i.e., “polished blades”, is not permitted.

C. Continued Airworthiness

(1)

Operators are urged to stay informed of airworthiness

information via Hartzell Service Bulletins and Service

Letters which are available from Hartzell distributors,

or from the Hartzell factory by subscription. Selected

information is also available on Hartzell Propeller’s web site

at www.hartzellprop.com.

OBSOLETE PROPELLER MODELS. SEE COVER PAGE

WARNINGS AND SERVICE BULLETIN HC-SB-61-331

Содержание HC-82VF-1



























































































































































































































































Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды

Hartzell HC-82VF-1, Руководство пользователя

Результаты поиска

Содержание HC-82VF-1

Отзывы:

Похожие инструкции для HC-82VF-1

Бренды по названию

Популярные бренды