manualshive.com logo in svg

Harris CZ1000F, Руководство по вводу в эксплуатацию

Поделиться
Скачать
Harris CZ1000F Скачать руководство пользователя страница 52

2-26

888-2685-001

12/24/07

 

WARNING: Disconnect primary power prior to servicing.

Section 2  Installation Verification & 

Ranger Commissioning Manual

Press transmitter off button to turn off RF output power.

Measure the antenna and transmission line impedance prior to application of RF 
power to the antenna system. The transmission line and antenna can be measured with 
a network analyzer prior to application of RF. 

!

 CAUTION:

MEASURE THE AMOUNT OF RF POWER ON THE ANTENNA TRANSMISSION LINE 
PRIOR TO MEASUREMENT WITH A NETWORK ANALYZER. IN SOME INSTANCES 
THE RF ENERGY FROM NEARBY STATIONS MAY BE PRESENT ON THE 
TRANSMISSION LINE IN AMOUNTS LARGE ENOUGH TO DAMAGE THE NETWORK 
ANALYZER. IN CASES LIKE THIS MEASUREMENTS MAY BE TAKEN WITH 
AMPLIFIERS USED TO AMPLIFY THE NETWORK ANALYZER SIGNAL SO THAT IT IS 
LARGE ENOUGH TO OVERCOME THE RFI PRESENT ON THE SYSTEM TO BE 
MEASURED.

Typical antenna system VSWR values are < 1.2:1 at the operating channel. If 
verification of antenna system VSWR is not possible then proceed with RF turn on at 
low levels and gradually increase power while monitoring reflected power levels. If 
significant reflected power levels are noted then measurement of the system will be 
required.

2.12

 

Parallel Remote Control Connections

External Parallel remote control units can interface at the External I/O Board in the rear 
of the cabinet. J13 through J17 are for remote Control, Status and Analog readings. The 
connectors are organized as follows:

•

J13 and J14 - Remote Transmitter Control Functions

•

J15 and J16 - Remote Status Outputs

•

J17 - Remote Analog Metering Outputs

NOTE:

The forward slash ( / ) in front of a signal name means active low. The signal /
INPUT 1 for example is activated by momentarily bringing that input low. Signal 
names without the forward slash are considered active high. This convention is 
used throughout the schematics.

Содержание CZ1000F



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды