Harmonic Ellipse 3000 Скачать руководство пользователя страница 91

Страница: 91 / 403

Chapter 4 Transport Stream Configuration

Ellipse 3000 Release 3.0, Rev. B

Services Sub-Menu/Tab

4.2.4.2

List or Drop PID Menu (Front Panel)

The List or Drop PID menu allows removing an elementary stream from the selected service.

To access the List or Drop PID parameter on the front panel:

❖

Navigate

Root > Configuration > Services > Service List > [Service Name] > List/Drop PID

The

Select PID to Drop

parameter displays a list of the available elementary streams to remove

from the service. This list includes all video and audio elementary streams currently active in the
selected service.

The

Drop

parameter deletes the selected elementary stream from the service. This option

executes the Drop command, not leading to a new screen.

List/Drop PID

1 Select PID to drop

Video H.264 - PID 513

2 Drop

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды