Harmonic Ellipse 3000 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 403

background image

Chapter 4 Transport Stream Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

73

Ellipse 3000 Release 3.0, Rev. B

General Sub-Menu/Tab

4.1.1

Output Rate

The

Output Rate

parameter defines the maximum possible output rate value of the transport-

stream and includes overhead.

In DSNG modules (Ellipse 3200), the actual output rate of the encoder can be set according to
either the Symbol Rate (from the Modulation menu) or the Output Rate (from the Transport
Stream menu). The actual rate is the rate last configured. This means that in DSNG modules (with
an IP or L-Band modulators), the actual output can be one of two settings:

■

Actual output rate is set according to the Symbol Rate (Modulation menu).

■

Actual output rate is set according to the Output Rate (Transport Stream menu).

The range is 350,000 to 160,000,000 bps. The Output Rate default value is

30,000,000

bps.

Front Panel:

4.1.2

Broadcast Standard

The

Broadcast Standard

parameter sets the stream broadcast standard to ATSC or DVB.

The available options are DVB and ATSC. The Broadcast Standard default is

DVB

.

Front Panel:

Output Rate

+30000000 [bps]

<00350000 - +70000000>

Broadcast Standard

1 ƒ DVB

2 ‚ ATSC

«
...
71
72
73
74
75
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellipse 3000

Бренд: Avermedia Страницы: 128

Бренд: XVision Страницы: 12

Бренд: Videoswitch Страницы: 64

4 Channel Network Video Recorder

Бренд: Entry-Level Страницы: 83

Бренд: Omnivision Страницы: 82

Бренд: Toshiba Страницы: 47

Бренд: Toshiba Страницы: 80

Бренд: Advanced Technology Video Страницы: 2

QuadraSplit 421SS

Бренд: Advanced Technology Video Страницы: 8

Бренд: Chinavision Страницы: 7

PS-7900MI Series

Бренд: Tgard Страницы: 170

Бренд: HIKVISION Страницы: 16

Бренд: HIKVISION Страницы: 63

Бренд: Q-See Страницы: 50

Бренд: PACOM Страницы: 102

Бренд: PACOM Страницы: 160

4 CH MPEG-4 DVR

Бренд: Colorado Security Products Страницы: 52

Бренд: Eyemax Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды