Harmonic Ellipse 3000 Скачать руководство пользователя страница 290 | Manualshive

Страница: 290 / 403

background image

Chapter 10 Unit Configuration

© 2013 Harmonic Inc. Harmonic All rights reserved.

290

Ellipse 3000 Release 3.0, Rev. B

Alarm Sub-Menu/Tab

10.5 Alarm Sub-Menu/Tab

The front panel

Alarm

sub-menu comprises the following sub-menus:

■

Alarm Configuration

– use to set alarm severity levels (None, Information, Warning or Critical)

■

Action Upon Critical Alarm

– enable to mute output ports when a critical alarm occurs

The Web Manager Alarm tab comprises the following:

■

Action Upon Critical Alarm

box – enable to mute output ports when a critical alarm occurs

■

Full list of alarms with configuration drop down menus – use to set alarm severity levels (None,
Info, Warning or Critical)

The

Alarm Configuration

sub-menu and the

Alarm

tab provide a list of all alarms defined for the

Ellipse. The following table lists and describes the Ellipse alarms:

Alarm Text

Alarm Behavior

Video Loss on SDI Input

No video on SDI Input

Video Loss on CV Input

No video on CV Input

Video 1 encoding failure

Any of the Video 1 through Video 4 has an actual video rate of more than
±20% the configured rate.

Audio 1/2/3/4 Input absent

Any of the Audio 1 through Audio 4 is missing
When the audio expansion card is used, alarms Audio 5/6/7/8 Input absent
are enabled.

Audio 1/2/3/4 encoding failure

Any of the Audio 1 thru Audio 4 has an actual audio rate of more than
±20% the configured rate.
When the audio expansion card is used, alarms Audio 5/6/7/8 fault are
enabled.

Multiplexer failure

MUX rate is different from the configured (set-up) rate.

Cascading rate failure

Cascading bit rate is different from configured (set-up) rate.

Cascade Service ID Conflict

High Temperature

One of the device temp sensor measures temperature either lower than

−

100°C or higher than +85°C

Fan A/B/C/ failure

Fan A, B or C not working

External (GPI) 1/2 triggered

Alarm indication on GPI 1/2

Modulator failure

Modulator board reports a hardware failure

Genlock absent

Active when the Genlock sync mode is selected

Compact Flash 99% full

Corrupted Data Base

User Data Base corrupted

DVBoIP Output 1/2 Disconnected

GbE Out port #1/2 address is not valid

«
...
288
289
290
291
292
...
»

Содержание Ellipse 3000




















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ellipse 3000

VANTAGE LH110 ECO SERIES

Бренд: Lorex Страницы: 5

Бренд: Plura Страницы: 37

Бренд: MYPIN Страницы: 25

Бренд: Techpro Страницы: 225

Бренд: TeleEye Страницы: 23

Бренд: Digisol Страницы: 70

Бренд: Grandstream Networks Страницы: 76

Бренд: Toworld18 Страницы: 18

Бренд: Velleman Страницы: 46

Бренд: IC Realtime Страницы: 136

Бренд: IC Realtime Страницы: 251

Бренд: DSE Страницы: 25

Бренд: DSE Страницы: 2

Бренд: DSE Страницы: 55

Бренд: DSE Страницы: 63

Бренд: Berghoch Страницы: 20

EVD-0130A1PRT-Mini DVR

Бренд: Euro Video Страницы: 2

Бренд: Euro Video Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды