Harmonic Ellipse 3000 Скачать руководство пользователя страница 281

Страница: 281 / 403

Chapter 10 Unit Configuration

281

Ellipse 3000 Release 3.0, Rev. B

Ellipse System Sub-Menu/Tab

10.3.8

BOOTP Control Menu

The Bootstrap Protocol (BOOTP) Control menu allows setting the basic parameters for managing
the operation of the BOOTP software updating protocol.

NOTE:

The BOOTP software update protocol is performed using the NMX application.

The available options are:

■

BOOTP Activation

– Enables/Disables updating the encoder software using BOOTP.

■

BOOTP Retries Count

– Sets the number of update tries for the BOOTP before failure is

declared. The range is 01 to 10 tries.

■

BOOTP Retry Time Out

– Sets the time out for each BOOTP try. The range is 01 to 10 sec.

Front Panel

To access the

BOOTP Control

menu on the front panel:

❖

Navigate

Root > Configuration > Unit > System > BOOTP Control

Web Manager

To access the

BOOTP Control

parameters in the Web Manager:

❖

Select

Unit > System

BOOTP Control

1 BOOTP Activation

Disabled

2 BOOTP Retries Count

3 BOOTP Retry Time Out

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды