Harmonic Ellipse 3000 Скачать руководство пользователя страница 270

Страница: 270 / 403

Chapter 10 Unit Configuration

270

Ellipse 3000 Release 3.0, Rev. B

Ellipse System Sub-Menu/Tab

10.3.3

Administration

■

WEB Needs PW – Use to configure the requirement of a password for Web Manager access.

■

Diagnostic Report – Use to generate a diagnostic report for field debugging.

■

Reset Device – Use to reset the device.

10.3.3.1

Viewing the Current Configuration

Front Panel

To view the current configuration on the front panel:

❖

Navigate

Root > Configuration > Unit > System > Administration

Administration

1 WEB needs PW

Disabled

2 Diagnostic Report

Idle

3 Reset Device

Idle

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Harmonic Ellipse 3000, Руководство пользователя, Страница: 270 / 403

Результаты поиска

Содержание Ellipse 3000

Отзывы: