Harmonic Ellipse 3000 Скачать руководство пользователя страница 112

Страница: 112 / 403

Chapter 4 Transport Stream Configuration

112

Ellipse 3000 Release 3.0, Rev. B

DPI Sub-Menu/Tab

4.5 DPI Sub-Menu/Tab

The DPI menu sets the parameters for a digital program insertion (Cue Tone trigger for
commercial needs). The signal is enabled in Audio analog mode.

The set-up options for each DPI parameters are:

■

DPI Activation

– Sets the DPI operational status.

Options: Disabled or Enabled (radio button selection). The default is

Disabled

■

PID

– Sets the PID of the elementary stream which carries the DPI information.

The range is 32 to 8190. The default is

1904

■

Time to Splice

– Sets the time to the next expected splice.

The range is +5 to +500 [Seconds]. The default is

■

Break Duration

– Sets the duration of the break for local material insertion.

The range is +1 to +500 [Seconds]. The default is

■

Duration Flag

– Indicates the presence of a duration break. (when set to 1).

Options: 0 or 1 (radio button selection). The default is

■

Auto Return

– Denotes that the break shall be used to mark the return to network feed.

Options: Disabled or Enabled (radio button selection). The default is

Disabled

■

Avails Expected

– Sets a the number of insertions expected in the current viewing event. The

range is 0 to +255. The default is

■

Unique Program ID

– Selects the Program ID which represents the content ID.

The range is 0x1 to 0xfff [Hex]. The default is

0x1

■

DPI Source

– Chooses the audio channel where the DPI information is included. Options: all

audio channels licensed to the unit (radio button selected). The default is

Audio CH#1 Left

Front Panel

To access the DPI menu on the front panel:

❖

Navigate

Root > Configuration > Transport Stream > DPI

to display the available program

insertion options.

DPI

1 DPI Input 1

2 DPI Input 2

Содержание Ellipse 3000















































































































































































































































































































































































































Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды

Harmonic Ellipse 3000, Руководство пользователя

Результаты поиска

Содержание Ellipse 3000

Отзывы:

Похожие инструкции для Ellipse 3000

Бренды по названию

Популярные бренды