Electra™ 9200 and ProStream
®
9100
Component Replacement Guide
Note
: The device must be turned off when removing and replacing
an I/O module. Use NMX or Standalone mode (ProStream only)
to make sure the service configuration is cleared before powering
down the system.
To remove an I/O module
:
1. Turn off the device.
2. Using a Phillips-head screwdriver, remove the two screws
attaching the module to the back of the chassis, as shown in step 2.
3. Pull firmly on the module to remove it from the chassis, as
shown in step 3.
Warning
: Wear the appropriate ESD protection when unpacking modules from their antistatic packing material.
Unpack and handle the module away from electric motors, transformers, and similar machinery.
To remove an AVPM card
:
1. Turn off the device.
2. Remove the bezel.
3. Remove the fan tray assembly.
4. Using a Phillips-head screwdriver, remove the screw attaching
the card retainer to the chassis, as shown in step 4.
5. For the Electra 9200, if a mini-SDI connector is present,
disconnect the connector identified in step 5.
6. Grab the card handle and slide the card from the chassis,
as shown in step 6.
To replace an AVPM card
:
1. From the front of the device, insert the card part way into
the chassis, as shown in step 1.
2. For the Electra 9200, if necessary, reinstall the mini-SDI
connector to the card, as shown in step 2.
Note
: On the Electra 9200, the cables for cards in slots 1 and 3 should
be tucked under the card cage so they don’t get pinched,
as indicated by the red circle.
3. Slide the card the rest of the way into the chassis until the module engages
with the chassis connector, as shown in step 3.
4. Reinstall the card retainer.
5. Reinsert the fan tray.
6. Reinstall the bezel.
Removing and Replacing an Input/Output (I/O) Module
Removing and Replacing an AVPM Card
This table shows module
configurations available
for the Electra 9200 and 9200D.
Note
: The AHC-561 audio card
is being deprecated on
the Electra 9200/9200D.
IOM-RAC2 and AHC-RAC
are the recommended
audio cards for that
encoder.
Module Slots
The illustrations below show the slot numbers of the dual power supply model of the Electra 9200 (ELC-9200D) and the ProStream 9100.
Note
: When facing the front of the device:
The bottom-left card is card 1. The top-left card is card 3.
The bottom-right card is card 2. The top-right card is card 4.
For support in Europe, Middle East:
Telephone: +44 1252 555 450
Email: [email protected]
For support in Africa:
Telephone: +972 54 900 7740
Email: [email protected]
For support in Russia:
Telephone: +7 495 926 4608
Email: [email protected]
For support in the Americas:
Telephone (Toll Free) +1 888 673 4896
Telephone (Local) +1 408 490 6477
Email: [email protected]
For support in China:
Telephone: +852 2116 1119
Email: [email protected]
For support in Asia-Pacific:
Telephone: +852 2116 1119
Email: [email protected]
For support in India:
Telephone: +91 22 6792 9291
Email: [email protected]
On the web:
www.harmonicinc.com/services-support
Technical Support
For complete Electra 9200 installation instructions, refer to the
Electra 9200 Installation Guide
.
For complete ProStream 9100 installation instructions, refer to the
ProStream 9000 Installation Guide
.
This table shows module
configurations available
for the ProStream 9100.
Module Slot Configurations
Warning
: The illustrations in this guide show the cover of the device removed. The illustrations were
created with the cover removed for ease of explanation. The cover should never be removed.
015-1806-001 Rev. E
2
2
3
2
1
2
Note
: Some procedures in this guide may vary between devices. Please read the
instructions carefully before replacing any components on your device.
Electra 9200
ProStream 9100
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Note
: The device needs to be turned off when removing and replacing
an AVPM card.
1
3
2
5
6
5
4
To replace an I/O module
:
1. Insert the module into an appropriate empty slot on the back of the chassis,
as shown in step 1.
2. Using a Phillips-head screwdriver, secure the module to the chassis, as
shown in step 2.
Make sure the module is level and goes into the device
smoothly without binding or scraping other modules.
The module must slide easily until you feel it engage
the internal connector and you see that it is flush with
the back of the device. Do not force the module.
Warning
:
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
FLEX -1
X
X
1 or 2 per chassis
IOM-RAC2
X
1 per chassis
Note: Must use slot 3
AHC-RAC
X
X
X
X
X
1 to 5 per chassis
AHC-561
X
X
X
X
1 to 4 per chassis
Note: Cannot be used with FLEX
8VSB
X
X
X
1 per chassis
ASI Out
X
X
1 per chassis
ASI In
X
X
X
1 per chassis
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Quad GbE
X
1 per chassis
Dual GbE
X
X
1 or 2 per chassis
8VSB
X
X
X
X
X
Up to 4 per chassis
ASI-SCR
X
X
X
X
X
Up to 5 per chassis
X
