background image

TEC0017    23Jan2015    P/N: 630-00027-01 revC

SL400 • Vantage Stair Lift Installation Manual

 9

Vantage Stair Lift

PREPARATION - CUTTING THE RAIL

Figure 9-1

CAUTION

Before cutting the rail, remove the 
gear rack, charge strips and wire 
from the rail.

 

 

TIP

When removing the gear rack  DO NOT 
remove the screws from the gear rack. If 
you do, the fastening plate will become 
lost within the channel and the gear 
rack will need to be removed.

CUTTING THE ALUMINUM RAIL

One Rail Installation (96 Inches or less)

1. Determine if the lift will be installed on the right or 
left side of the staircase. 

[Figure 9-1]

When deciding on which side of the staircase to install 
the lift, consider:

• 

Which side offers access to an electrical outlet?

• 

Which side has protruding obstructions such as 
handrails or wall or window trim?

• 

Is there a doorway  at the top or bottom?

2. Determine top and bottom of rail. The teeth of the 
gear rack must face toward the wall nearest to where 
the lift will be installed. 

3. Remove the charge strips and wiring from the rail.

4. Cut the rail to length.

5. Replace charge strips in both ends of the rail routing 
the wire through the main interior channel. 

[Figure 9-2]

MAIN INTERIOR CHANNEL

Figure 9-2

Содержание Vantage SL400



































Отзывы: