background image

Outside Vehicle Lifts:

  Installation & Service Manual

06DEC19  |  P/N: 630-00106 REV A

19

OUTSIDE VEHICLE LIFTS:

 

SECTION 5

CHAIR PREPARATION

Section 5

Chair Preparation

A lift with four securement straps offers two options 
for attaching strap hooks to the chair—the anchor 
plate or the U-bolt kit. The lift includes both sets of 
options.

ANCHOR PLATE

The anchor plate is a flat plate and may vary in length 
depending on the mobility device used. The anchor 
plate attaches to the bottom of any chair or scooter 
that has a center seat post. See Figure 5-1.

Figure 5-1

The anchor plate should extend about 11/2

"

 out from 

the side of the cushion. To secure the chair to the 
lift, the user can attach the strap hooks to the anchor 
plate. See Figure 5-2.

Anchor Plate Installation

1. 

Remove the seat from the chair.

2. 

Loosen the screws that attach the plate to the 
bottom of the seat. Allow enough room to slide 
the anchor plate between the seat and the seat 
plate.

3. 

Attach the anchor plate to the center of the 
seat plate with the holes on each end extending 
evenly on each side of the seat.

4. 

Retighten the screws that hold the seat plate to 
the bottom of the seat.

5. 

Replace the seat on the chair.

Figure 5-2

Содержание AL003





































Отзывы: