Harmar Mobility AL003 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

Harmar Mobility AL003 Скачать руководство пользователя страница 15

Outside Vehicle Lifts:

Installation & Service Manual

06DEC19 | P/N: 630-00106 REV A

15

OUTSIDE VEHICLE LIFTS:

SECTION 4

INSTALLATION

Optimizing Hitch Height

You can change the height of the lift by adjusting the
hitch adaptor’s orientation and location on a standard
hitch adaptor. Changing the height of the lift helps
you optimize the vehicle’s ground clearance to ensure
that the platform lies flat when it reaches the end of
its travel. To select the orientation needed for the
vehicle based on the hitch height (the distance of the
vehicle’s hitch receiver to the ground). Refer to Figure
3-6 on page 9 and chart on page 10.

HITCH ADAPTOR

INSTALLATION

1.

Attach the hitch adaptor to the hitch post,
ensuring that the adaptor is properly oriented
with the post according to the application’s hitch
height. See Figure 4-09.

Figure 4-09

2.

Attach the hitch post to the lift, but DO NOT
overtighten it.

3.

Insert the hitch adaptor into the receiver on the
vehicle’s hitch. Secure the adaptor according to
the hitch class. See Figure 4-10.

Figure 4-10

NOTE: ONLY the standard hitch adaptors or class 3 - 2

"

drop can be safely inverted.

Pinch

Bolt

Tube

1/2" H

ex

Nyloc N

ut

1/2" H

ex

Nyloc N

ut

Threaded

Hole

HHCS,

1/2"-13" x 3"

Fully Threaded

HHCS,

1/2"-13" x 3 1/2" or 4"

Fully Threaded

Presses Hitch

Adaptor against

receiver wall

eliminating

rattles, and lift

movements

CLASS 2

CLASS 3

1/2

"

Hex

Nyloc

Nuts (x3)

HHCS,

1/2

"

-13

"

x 3 1/2

"

(x3)

or

Hardware supplied in hardware pack

«
...
13
14
15
16
17
...
»

Содержание AL003





































Отзывы:

Нет отзывов