background image

9

P43 Pellet Stove

OPtiOnS

Side heat Shields

Side  heat  shields  are  available  to  reduce  the 

clearance to combustible materials. 

Part #1-00-00000

hopper extension

The hopper extension allows you to put more pellet 

fuel in the hopper and extends burn time on one 

load  of  pellets. The  hopper  extension  adds  60 

pounds to the existing 60 pound hopper capacity, 

allowing you to load 10 pounds of pellets at one 

time. 

Part #1-00-08536

decorative tile/grey Slate Options

The decorative tile and slate measure 11.938" x 

5.938". The tile/slate frame is necessary to hold 

the tile or slate in place on the stove. There are 

10 decorative tile choices, and 4 decorative slate 

choices. See dealer for samples.

The Brushed Stainless deer cutout, pictured below, 

is another option available. This cutout reveals the 

color of the stove through the cut out shapes.

5.938"

11.938"

frame

tile/slate

direct vent wall Passthrough Kit 

You may choose to use the 

optional  Direct  Vent  Wall 

Passthrough Kit (part #1-00-

677077) which incorporates 

v e n t i n g   p a s s t h r o u g h 

and  outside  air  into  one 

component. 

Содержание P43

































Отзывы: