Harman Martin MAC Aura PXL Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 46

background image

4

MAC Aura PXL User Guide

Introduction

Warning! Before installing, operating or servicing the MAC Aura PXL, read the latest version of the
product’s Safety and Installation Manual, paying particular attention to the Safety Precautions
section. The Safety and Installation Manual is supplied with the fixture. The latest version is also
available for download from the MAC Aura PXL area of the Martin website at www.martin.com.

This User Guide is a supplement to the Installation and Safety Manual that is supplied with the MAC Aura
PXL. Both these documents are available for download from the MAC Aura PXL area of the Martin® website
at www.martin.com. This User Guide contains information that is mainly of interest for lighting designers and
operators, whereas the Safety and Installation Manual contains important information for all users,
especially installers and technicians.

We recommend that you check the Martin website regularly for updated documentation, because we
publish revised versions each time we can improve the quality of the information we provide and each time
we release new firmware with changes or new features. Each time we revise this guide we list any important
changes on page 2 so that you can keep track of updates.

Operating the fixture

Before applying power to or operating the MAC Aura PXL:

• Read the ‘Safety Information’ section of the fixture’s Safety and Installation Manual.

• Check that the installation is safe and secure.

• Check that the base is fastened securely so that the torque reaction when the head moves will not cause

the base to move.

• Check that the head tilt lock is released.

• Be prepared for the fixture to light up suddenly. Check that no-one is looking at the fixture from close

range.

• Be prepared for the head to move suddenly. Check that there will be no risk of collision with persons or

objects.

The MAC Aura PXL does not have an On/Off switch. To apply power to the fixture, apply power to the power
input cable.

«
...
2
3
4
5
6
...
»

Содержание Martin MAC Aura PXL















































Отзывы:

Нет отзывов

Похожие инструкции для Martin MAC Aura PXL

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Tetrix 351 AC/DC Smart FW

Бренд: EWM Страницы: 117

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Lab companion SI-300

Бренд: Jeio tech Страницы: 69

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: TANDBERG Страницы: 23

Бренд: Yetter Страницы: 24

Бренд: GE Страницы: 176

Бренд: Triton Blue Страницы: 11

Бренд: Calibre Fitness Страницы: 11

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Бренд: Exalto Страницы: 28

Бренд: PURE Страницы: 16

Бренд: POOL LAB Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды