background image

17 

Control settings 

Setting the host-client link mode 

It is possible to control several machines from one digital remote control. The 
machine with the remote plugged into it is set as the Host. The other machines 
are set as Clients. The machines are interconnected with DMX cabling. 
 

Use the Previous / Next buttons to select the LINK MODE option from the 
SETTINGS menu. 
Use the Up/Down buttons to select RECEIVE (client unit) or SEND (host unit). 
Press the ENTER button to store the link setting. 
 
The machine should be set to SEND only if it is running as a host. If running as a 
client, stand-alone or DMX controlled it should be set to RECEIVE. If a machine 
set to SEND is connected to an active DMX system, the DMX will be corrupted 
causing flickering of lights and other strange symptoms. 
 

 

Priming the machine after fluid out 

If the machine runs out of fluid it will automatically shut down and show FLUID 
OUT on the display to prevent damage to the pump(s). To suck the new fluid 
back into the machine and reset the FLUID OUT error, replace/refill the fluid 
reservoir and use the prime function. 
 
Use the Previous / Next buttons to select the PRIME option from the SETTINGS 
menu. 
Use the Up/Down buttons to change the option to YES. 

Press the ENTER button to start the priming function. 
 
The pump(s) will operate at full power for a short time to purge air from the 
pipes inside the unit.  
To exit this menu if you decide not to activate the Prime function, select NO and 
press ENTER.  
To terminate a running prime operation, enter YES and press enter. 
Prime can also be initiated and terminated from DMX channel 2 (in two channel 
mode) 

 

Resetting options to factory settings 

The factory settings configure a standard mode of operation for the machine. 
 
Use the Previous / Next buttons to select the RESET option from the SETTINGS 
menu. 
Use the Up/Down buttons to change the option to YES. 
Press the ENTER button to reset all options. 
 
To exit this menu if you decide not to reset the options, select NO and press 
ENTER. 

 
 

Содержание Martin JEM ZR Series

































Отзывы: